Drawing → BOQ
← Mindmapwhat the drawings said

Washer

2 pages · 3 crops · ×3 · other

⚠ No class in the bridge ontology fits this itemAdd a class

The ontology would need a structural washer class.

Every dimension read for it8

  • 1/4" x 3/2" inWasher sizep10 · p10_r08
  • 1 in1" CL.not attributedp11 · p11_r04 recess detail for diaphragm bar ends
  • 3 in3"not attributedp11 · p11_r04 recess detail for diaphragm bar ends
  • 5 in5" DIA.not attributedp11 · p11_r04 recess detail for diaphragm bar ends
  • 1" in1" CL.not attributedp11 · p11_r04
  • 3" in3"not attributedp11 · p11_r04
  • 4" in4" EACH WAYnot attributedp11 · p11_r04
  • 5" in5" DIAnot attributedp11 · p11_r04

Notes on the sheets that carry it

  • p10DIAPHRAGM BAR SHALL BE A 1" DIAMETER PLAIN BAR, THREADED 5" ON EACH END, WITH 1/4" X 3/2" DIAMETER WASHERS AND HEX NUTS (ASTM A 709 GRADE 36).
  • p10TIGHTEN DIAPHRAGM BAR AS PER SUB-SECTION 507.3.05.C OF THE GEORGIA DOT SPECIFICATIONS.
  • p10AFTER EXCESS DIAPHRAGM BAR HAS BEEN CUT OFF, PAINT DIAPHRAGM BAR, WASHER, AND NUT EXPOSED IN RECESS WITH SPECIAL PROTECTIVE COATING NO. 2 P AS PER SECTION 535 OF THE GEORGIA DOT SPECIFICATIONS. AFTER PAINTING, FILL THE RECESS WITH AN APPROVED EPOXY GROUT.
  • p10GALVANIZING OF THE DIAPHRAGM BAR AS PER SUB-SECTION 865.2.0I.B.12 OF THE GEORGIA DOT SPECIFICATIONS IS NOT
  • p11GALVANIZING OF THE DIAPHRAGM BAR AS PER SUB-SECTION 865.2.01.B.12 OF THE GEORGIA DOT SPECIFICATIONS IS NOT REQUIRED.
  • p11RECESS DETAIL FOR DIAPHRAGM BAR ENDS
  • p11DIAPHRAGM BAR SHALL BE A 1" DIAMETER PLAIN BAR, THREADED 5" ON EACH END, WITH ¼" X 3/2" DIAMETER WASHERS AND HEX NUTS (ASTM A 709 GRADE 36).

Every crop it was read in — the drawing beside what the model took off it

Page 10

crop

p10_r08

page 10 · other_p10_r08
Original
p10_r08
{
  "view": "Notes",
  "objects": [
    {
      "name": "Diaphragm bar",
      "tag": "",
      "shape": "circular",
      "material": "reinforcing steel (plain bar)",
      "count": 1,
      "note": "1\" diameter; threaded 5\" on each end"
    },
    {
      "name": "Washer",
      "tag": "",
      "shape": "circular",
      "material": "steel washer",
      "count": null,
      "note": "1/4\" x 3/2\" diameter washers"
    },
    {
      "name": "Hex nut",
      "tag": "",
      "shape": "circular",
      "material": "steel",
      "count": null,
      "note": "hex nuts (ASTM A 709 GRADE 36)"
    },
    {
      "name": "Epoxy grout",
      "tag": "",
      "shape": "bulk",
      "material": "epoxy grout",
      "count": null,
      "note": "exposed in recess after painting"
    },
    {
      "name": "Protective coating No. 2P",
      "tag": "",
      "shape": "layer",
      "material": "protective coating",
      "count": null,
      "note": "special protective coating No. 2 P as per section 535"
    },
    {
      "name": "Galvanizing (not complete)",
      "tag": "",
      "shape": "process",
      "material": "galvanizing",
      "count": null,
      "note": "GALVANIZING OF THE DIAPHRAGM BAR AS PER SUB-SECTION 865.2.0I.B.12 OF THE GEORGIA DOT SPECIFICATIONS IS NOT"
    }
  ],
  "measurements": [
    {
      "label": "Diaphragm bar diameter",
      "value": "1\"",
      "unit": "in",
      "appliesTo": "Diaphragm bar"
    },
    {
      "label": "Thread length",
      "value": "5\"",
      "unit": "in",
      "appliesTo": "Diaphragm bar"
    },
    {
      "label": "Washer size",
      "value": "1/4\" x 3/2\"",
      "unit": "in",
      "appliesTo": "Washer"
    }
  ],
  "notes": [
    "DIAPHRAGM BAR SHALL BE A 1\" DIAMETER PLAIN BAR, THREADED 5\" ON EACH END, WITH 1/4\" X 3/2\" DIAMETER WASHERS AND HEX NUTS (ASTM A 709 GRADE 36).",
    "TIGHTEN DIAPHRAGM BAR AS PER SUB-SECTION 507.3.05.C OF THE GEORGIA DOT SPECIFICATIONS.",
    "AFTER EXCESS DIAPHRAGM BAR HAS BEEN CUT OFF, PAINT DIAPHRAGM BAR, WASHER, AND NUT EXPOSED IN RECESS WITH SPECIAL PROTECTIVE COATING NO. 2 P AS PER SECTION 535 OF THE GEORGIA DOT SPECIFICATIONS. AFTER PAINTING, FILL THE RECESS WITH AN APPROVED EPOXY GROUT.",
    "GALVANIZING OF THE DIAPHRAGM BAR AS PER SUB-SECTION 865.2.0I.B.12 OF THE GEORGIA DOT SPECIFICATIONS IS NOT"
  ],
  "labels": [],
  "description": "Crop shows a notes block detailing diaphragm bar fabrication and finishing per Georgia DOT specs: 1 inch diameter plain bar with 5 inch thread ends, washers and nuts, coating No. 2P, epoxy grout fill, and a note on galvanizing."
}

p10_r08Notes

  • Washercircularsteel washer1/4" x 3/2" diameter washers

1" in Diaphragm bar diameter5" in Thread length1/4" x 3/2" in Washer size

Page 11

crop

p11_r04 recess detail for diaphragm bar ends

page 11 · gdot_drawing_0a6d24ffdd874879a37c7122f1fd8bef_p11_r04_recess_detail_for_diaphragm_bar_ends
Original
p11_r04 recess detail for diaphragm bar ends
{
  "view": "Detail",
  "objects": [
    {
      "name": "Diaphragm bar",
      "tag": "",
      "shape": "circular",
      "material": "plain steel",
      "count": 1,
      "note": ""
    },
    {
      "name": "Washer",
      "tag": "",
      "shape": "circular",
      "material": "metal",
      "count": 1,
      "note": ""
    },
    {
      "name": "Hex nut",
      "tag": "",
      "shape": "hexagonal",
      "material": "steel (ASTM A 709 Grade 36)",
      "count": 2,
      "note": ""
    },
    {
      "name": "Hole",
      "tag": "",
      "shape": "circular",
      "material": "drilled",
      "count": 1,
      "note": "2\" DIAMETER HOLE"
    }
  ],
  "measurements": [
    {
      "label": "1\" CL.",
      "value": "1",
      "unit": "in",
      "appliesTo": ""
    },
    {
      "label": "3\"",
      "value": "3",
      "unit": "in",
      "appliesTo": ""
    },
    {
      "label": "2\" DIAMETER HOLE",
      "value": "2",
      "unit": "in",
      "appliesTo": "Hole"
    },
    {
      "label": "CUT OFF EXCESS DIAPHRAGM BAR",
      "value": "1",
      "unit": "in",
      "appliesTo": "Beam face"
    },
    {
      "label": "5\" DIA.",
      "value": "5",
      "unit": "in",
      "appliesTo": ""
    }
  ],
  "notes": [
    "DIAPHRAGM BAR SHALL BE A 1\" DIAMETER PLAIN BAR, THREADED 5\" ON EACH END, WITH 1/4\" X 3/2\" DIAMETER WASHERS AND HEX NUTS (ASTM A 709 GRADE 36).",
    "TIGHTEN DIAPHRAGM BAR AS PER SUB-SECTION 507.3.05.C OF THE GEORGIA DOT SPECIFICATIONS.",
    "AFTER EXCESS DIAPHRAGM BAR HAS BEEN CUT OFF, PAINT DIAPHRAGM BAR, WASHER, AND NUT EXPOSED IN RECESS WITH SPECIAL PROTECTIVE COATING NO.2 P AS PER SECTION 535 OF THE GEORGIA DOT SPECIFICATIONS. AFTER PAINTING, FILL THE RECESS WITH AN APPROVED EPOXY GROUT.",
    "GALVANIZING OF THE DIAPHRAGM BAR AS PER SUB-SECTION 865.2.01.B.12 OF THE GEORGIA DOT SPECIFICATIONS IS NOT REQUIRED.",
    "RECESS DETAIL FOR DIAPHRAGM BAR ENDS"
  ],
  "labels": [
    "RECESS DETAIL FOR DIAPHRAGM BAR ENDS"
  ],
  "description": "Detail of the diaphragm bar end recess showing a 2 inch diameter hole, a 1 inch diameter diaphragm bar with threaded ends, a bolt and nut/washer assembly, and a note to cut off excess bar 1 inch from the beam face with specified coating and epoxy fill."
}

p11_r04 recess detail for diaphragm bar endsDetail

  • Washer×1circularmetal

1 in 1" CL.3 in 3"2 in 2" DIAMETER HOLE1 in CUT OFF EXCESS DIAPHRAGM BAR5 in 5" DIA.

crop

p11_r04

page 11 · other_p11_r04
Original
p11_r04
{
  "view": "Detail",
  "objects": [
    {
      "name": "diaphragm bar",
      "tag": "",
      "shape": "circular",
      "material": "steel",
      "count": 1,
      "note": "1\" DIAMETER PLAIN BAR; THREADED ENDS"
    },
    {
      "name": "washer",
      "tag": "",
      "shape": "circular",
      "material": "metal",
      "count": 2,
      "note": "1/4\" X 3/2\" DIAMETER WASHERS"
    },
    {
      "name": "nut",
      "tag": "",
      "shape": "hexagonal",
      "material": "steel",
      "count": 2,
      "note": "HEX NUTS (ASTM A 709 GRADE 36)"
    },
    {
      "name": "hole",
      "tag": "",
      "shape": "circular",
      "material": "",
      "count": 1,
      "note": "2\" DIAMETER HOLE"
    }
  ],
  "measurements": [
    {
      "label": "1\" CL.",
      "value": "1\"",
      "unit": "in",
      "appliesTo": ""
    },
    {
      "label": "3\"",
      "value": "3\"",
      "unit": "in",
      "appliesTo": ""
    },
    {
      "label": "4\" EACH WAY",
      "value": "4\"",
      "unit": "in",
      "appliesTo": ""
    },
    {
      "label": "5\" DIA",
      "value": "5\"",
      "unit": "in",
      "appliesTo": ""
    },
    {
      "label": "2\" DIAMETER HOLE",
      "value": "2\"",
      "unit": "in",
      "appliesTo": "hole"
    }
  ],
  "notes": [
    "DIAPHRAGM BAR SHALL BE A 1\" DIAMETER PLAIN BAR, THREADED 5\" ON EACH END, WITH ¼\" X 3/2\" DIAMETER WASHERS AND HEX NUTS (ASTM A 709 GRADE 36).",
    "TIGHTEN DIAPHRAGM BAR AS PER SUB-SECTION 507.3.05.C OF THE GEORGIA DOT SPECIFICATIONS.",
    "AFTER EXCESS DIAPHRAGM BAR HAS BEEN CUT OFF, PAINT DIAPHRAGM BAR, WASHER, AND NUT EXPOSED IN RECESS WITH SPECIAL PROTECTIVE COATING NO. 2 P AS PER SECTION 535 OF THE GEORGIA DOT SPECIFICATIONS. AFTER PAINTING, FILL THE RECESS WITH AN APPROVED EPOXY GROUT.",
    "GALVANIZING OF THE DIAPHRAGM BAR AS PER SUB-SECTION 865.2.01.B.12 OF THE GEORGIA DOT SPECIFICATIONS IS NOT REQUIRED."
  ],
  "labels": [
    "RECESS DETAIL FOR DIAPHRAGM BAR ENDS"
  ],
  "description": "Detail view showing the recess for diaphragm bar ends with a 1\" diameter diaphragm bar, threaded ends, washers and nuts, and a 2\" diameter hole. Includes notes on material, coating, and installation requirements for the end details."
}

p11_r04Detail

  • washer×2circularmetal1/4" X 3/2" DIAMETER WASHERS

1" in 1" CL.3" in 3"4" in 4" EACH WAY5" in 5" DIA2" in 2" DIAMETER HOLE