Drawing → BOQ
← Mindmapwhat the drawings said

Epoxy Grout

1 page · 2 crops · material

⚠ No class in the bridge ontology fits this itemAdd a class

The ontology would need an epoxy grout material class.

Notes on the sheets that carry it

  • p10⊛ DIAPHRAGM BAR SHALL BE A 1” DIAMETER PLAIN BAR, THREADED 5” ON EACH END, WITH 1/4” X 3 1/2” DIAMETER WASHERS AND HEX NUTS (ASTM A 709 GRADE 36).
  • p10TIGHTEN DIAPHRAGM BAR AS PER SUB-SECTION 507.3.05.C OF THE GEORGIA DOT SPECIFICATIONS.
  • p10AFTER EXCESS DIAPHRAGM BAR HAS BEEN CUT OFF, PAINT DIAPHRAGM BAR, WASHER, AND NUT EXPOSED IN RECESS WITH SPECIAL PROTECTIVE COATING NO. 2 P AS PER SECTION 535 OF THE GEORGIA DOT SPECIFICATIONS. AFTER PAINTING, FILL THE RECESS WITH AN APPROVED EPOXY GROUT.
  • p10GALVANIZING OF THE DIAPHRAGM BAR AS PER SUB-SECTION 865.2.01.B.12 OF THE GEORGIA DOT SPECIFICATIONS IS NOT [partial]

Every crop it was read in — the drawing beside what the model took off it

Page 10

crop

p10_r08 tighten diaphragm bar as per sub section

page 10 · gdot_drawing_83a3db2262b94086918a1e232d2b9607_p10_r08_tighten_diaphragm_bar_as_per_sub_section
Original
p10_r08 tighten diaphragm bar as per sub section
{
  "view": "Notes",
  "objects": [
    {
      "name": "Diaphragm bar",
      "tag": "",
      "shape": "circular",
      "material": "",
      "count": null,
      "note": "Plain bar, threaded 5” on each end."
    },
    {
      "name": "Washer",
      "tag": "",
      "shape": "circular",
      "material": "",
      "count": null,
      "note": "Used with diaphragm bar."
    },
    {
      "name": "Hex nut",
      "tag": "",
      "shape": "hexagonal",
      "material": "",
      "count": null,
      "note": "ASTM A 709 Grade 36."
    },
    {
      "name": "Epoxy grout",
      "tag": "",
      "shape": "",
      "material": "",
      "count": null,
      "note": "Approved epoxy grout for recess."
    }
  ],
  "measurements": [
    {
      "label": "Diaphragm bar diameter",
      "value": "1”",
      "unit": "",
      "appliesTo": "Diaphragm bar"
    },
    {
      "label": "Threaded length on each end",
      "value": "5”",
      "unit": "",
      "appliesTo": "Diaphragm bar"
    },
    {
      "label": "Washer thickness",
      "value": "1/4”",
      "unit": "",
      "appliesTo": "Washer"
    },
    {
      "label": "Washer diameter",
      "value": "3 1/2”",
      "unit": "",
      "appliesTo": "Washer"
    }
  ],
  "notes": [
    "⊛ DIAPHRAGM BAR SHALL BE A 1” DIAMETER PLAIN BAR, THREADED 5” ON EACH END, WITH 1/4” X 3 1/2” DIAMETER WASHERS AND HEX NUTS (ASTM A 709 GRADE 36).",
    "TIGHTEN DIAPHRAGM BAR AS PER SUB-SECTION 507.3.05.C OF THE GEORGIA DOT SPECIFICATIONS.",
    "AFTER EXCESS DIAPHRAGM BAR HAS BEEN CUT OFF, PAINT DIAPHRAGM BAR, WASHER, AND NUT EXPOSED IN RECESS WITH SPECIAL PROTECTIVE COATING NO. 2 P AS PER SECTION 535 OF THE GEORGIA DOT SPECIFICATIONS. AFTER PAINTING, FILL THE RECESS WITH AN APPROVED EPOXY GROUT.",
    "GALVANIZING OF THE DIAPHRAGM BAR AS PER SUB-SECTION 865.2.01.B.12 OF THE GEORGIA DOT SPECIFICATIONS IS NOT [partial]"
  ],
  "labels": [],
  "description": "This crop is a block of construction notes for diaphragm bars, washers, and hex nuts. It specifies bar threading, tightening, protective coating after cutting, and filling the recess with approved epoxy grout; the final galvanizing note is cut off."
}

p10_r08 tighten diaphragm bar as per sub sectionNotes

  • Epoxy groutApproved epoxy grout for recess.

1” Diaphragm bar diameter5” Threaded length on each end1/4” Washer thickness3 1/2” Washer diameter

crop

p10_r08

page 10 · other_p10_r08
Original
p10_r08
{
  "view": "Notes",
  "objects": [
    {
      "name": "Diaphragm bar",
      "tag": "",
      "shape": "plain bar",
      "material": "",
      "count": null,
      "note": "Threaded 5” on each end."
    },
    {
      "name": "Washer",
      "tag": "",
      "shape": "circular",
      "material": "",
      "count": null,
      "note": "Specified as 1/4” x 3 1/2” diameter."
    },
    {
      "name": "Hex nut",
      "tag": "",
      "shape": "hexagonal",
      "material": "ASTM A 709 Grade 36",
      "count": null,
      "note": ""
    },
    {
      "name": "Recess",
      "tag": "",
      "shape": "",
      "material": "",
      "count": null,
      "note": "To receive approved epoxy grout after painting."
    },
    {
      "name": "Special protective coating",
      "tag": "NO. 2 P",
      "shape": "",
      "material": "",
      "count": null,
      "note": "For exposed diaphragm bar, washer, and nut in recess."
    },
    {
      "name": "Epoxy grout",
      "tag": "",
      "shape": "",
      "material": "approved epoxy grout",
      "count": null,
      "note": "To fill recess after painting."
    }
  ],
  "measurements": [
    {
      "label": "diaphragm bar diameter",
      "value": "1”",
      "unit": "",
      "appliesTo": "Diaphragm bar"
    },
    {
      "label": "threaded length on each end",
      "value": "5”",
      "unit": "",
      "appliesTo": "Diaphragm bar"
    },
    {
      "label": "washer dimension",
      "value": "1/4” x 3 1/2”",
      "unit": "",
      "appliesTo": "Washer"
    }
  ],
  "notes": [
    "DIAPHRAGM BAR SHALL BE A 1” DIAMETER PLAIN BAR, THREADED 5” ON EACH END, WITH 1/4” X 3 1/2” DIAMETER WASHERS AND HEX NUTS (ASTM A 709 GRADE 36).",
    "TIGHTEN DIAPHRAGM BAR AS PER SUB-SECTION 507.3.05.C OF THE GEORGIA DOT SPECIFICATIONS.",
    "AFTER EXCESS DIAPHRAGM BAR HAS BEEN CUT OFF, PAINT DIAPHRAGM BAR, WASHER, AND NUT EXPOSED IN RECESS WITH SPECIAL PROTECTIVE COATING NO. 2 P AS PER SECTION 535 OF THE GEORGIA DOT SPECIFICATIONS. AFTER PAINTING, FILL THE RECESS WITH AN APPROVED EPOXY GROUT.",
    "GALVANIZING OF THE DIAPHRAGM BAR AS PER SUB-SECTION 865.2.01.B.12 OF THE GEORGIA DOT SPECIFICATIONS IS NOT (partial)."
  ],
  "labels": [],
  "description": "This crop is a block of construction notes concerning diaphragm bars, washers, and hex nuts. It specifies threading, tightening, coating, and epoxy-grouting requirements; the final galvanizing note is cut off."
}

p10_r08Notes

  • Epoxy groutapproved epoxy groutTo fill recess after painting.

1” diaphragm bar diameter5” threaded length on each end1/4” x 3 1/2” washer dimension