Drawing → BOQ
← Mindmapwhat the drawings said

Pier Cap

3 pages · 7 crops · ×8 · substructure

Matched toPier Capbridge.substructure.pier_system.pier_capon “Pier cap”

3 read off the drawings · 1 derived · 1 not established
The class asks forValueHowFrom
LengthLwants m/mmnot establishedAll five crops that dimension the pier cap in plan give only one horizontal figure, which the drawings themselves label 'pier cap width' (SQ 3640 / SK 4203). No second, orthogonal plan dimension for the cap itself is stated (the 1500 value belongs to the RCC column pier, a different item). Without a second figure, 'Length' cannot be read or derived.not found
WidthWwants m/mm3640 (SQ) / 4203 (SK) mmDirectly read from drawing labels '3640(SQ)' and '4203(SK)' each explicitly annotated as 'pier cap width' in Section B-B views.All four sectional views of pier P1 consistently label this dimension 'pier cap width', with a square (SQ) value of 3640 mm and a skew (SK) value of 4203 mm due to the skewed bridge alignment. Both values are explicitly owned by the pier cap object, so this is a direct read, though which one governs (square vs skew) is a design choice not stated.readp2 · p02_r10p2 · pier_p1p2 · p02_r09 section b bp2 · p02_r10 section b b
ThicknessTwants m/mm1500 mm750 (upper tier) + 750 (lower tier) = 1500 mm, matching the directly labeled 'Total pier cap depth/height' of 1500 mm in the same views.The pier cap is shown as a two-tier block, each tier 750 mm deep, summing to a total cap depth/height of 1500 mm, which is also independently stated as 'pier cap height' / 'Total bearing pedestal height' / 'Total pier cap depth' across multiple crops, confirming the value directly.derivedp2 · p02_r10p2 · pier_p1p2 · p02_r09 section b bp2 · p02_r10 section b b
Instance CountNwants count1 countObject list in crop 'bridge_pier_and_foundation_p02_r10' states 'Pier cap / bearing seat' count: 1 for pier P1; no other pier cap marks appear in the supplied readings.Only pier P1 is documented in the given crops, with a single pier cap sitting atop the single column pier. No other pier marks (e.g., P2, P3) are present in the supplied readings, so the count established here is 1; a full bridge may have more piers not covered by these crops.readp2 · p02_r10p2 · pier_p1
Concrete GradefckM50General design notes concrete-grade table lists 'BEARING PEDESTAL' = M50; the item's aliases explicitly include 'bearing pedestal / pier cap block' and 'bearing pedestal'.The notes table separates 'ABUTMENT & PIER' (M45) from 'BEARING PEDESTAL' (M50). Since the pier cap is the bearing-pedestal element (per the item's alternate names) sitting atop the pier column, its concrete grade is M50, distinct from the pier column's M45. This linkage relies on alias matching rather than an explicit 'PIER CAP' row, so confidence is lower.readcheckp2 · p02_r06 notes of general design notes

Worked out by anthropic/claude-sonnet-5 from the readings below, which are the source. A derived value shows its arithmetic — check it against the drawing before it is priced.

How the sheets named it

Pier/Pier capPier cap / bearing pedestalPier cap / pier headPier cap / pier bearing seatSection element at pier location (likely girder/beam or pier cap cross-section)Pier cap / pile cap top and bottom levels (PCTL/PCBL)P1

Every dimension read for it20

  • 1170Offset at P1 (square)p1 · p01_r09
  • 1350Offset at P1 (skew)p1 · p01_r09
  • 1500Pier cap total depthp2 · p02_r10
  • 750Pier cap depth split (upper)p2 · p02_r10
  • 750Pier cap depth split (lower)p2 · p02_r10
  • 750Pier cap height segmentp2 · pier_p1
  • 750Pier cap height segment (second)p2 · pier_p1
  • 1500Pier cap total heightp2 · pier_p1
  • 3640Pier cap plan dimension (SQ)p2 · pier_p1
  • 4203Pier cap plan dimension (SK)p2 · pier_p1
  • 750 mmPier cap layer thicknessp2 · p02_r09 section b b
  • 750 mmPier cap layer thicknessp2 · p02_r09 section b b
  • 1500 mmTotal pier cap depthp2 · p02_r09 section b b
  • 3640 mmPier cap width (SQ)p2 · p02_r09 section b b
  • 4203 mmPier cap width (SK)p2 · p02_r09 section b b
  • 750Pier cap depth upperp2 · p02_r10 section b b
  • 750Pier cap depth lowerp2 · p02_r10 section b b
  • 1500Pier cap total depthp2 · p02_r10 section b b
  • 3640(SQ)Pier cap width (square)p2 · p02_r10 section b b
  • 4203(SK)Pier cap width (skew)p2 · p02_r10 section b b

Notes on the sheets that carry it

  • p1HALF PLAN SHOWING DECK LEVEL
  • p1HALF PLAN SHOWING FOUNDATION LEVEL
  • p1(SCALE 1:300)
  • p130° SKEW
  • p15000 (TYP.)
  • p2RCC CRASH BARRIER
  • p2FRL
  • p2DECK CONTINUITY
  • p2PRECAST PSC GIRDER (TYP.)
  • p2RCC SEISMIC STOPPER
  • p2POT-PTFE BEARING (TYP.)
  • p2RCC COLUMN PIER
  • p2RCC PILECAP
  • p21200 DIA BORED CAST-IN-SITU PILES
  • p2CHAMFER
  • p2CHAMFER 25X25
  • p3READ THIS DRAWING IN CONJUNCTION WITH OTHER SHEETS OF THE SAME DRAWING NUMBER

Every crop it was read in — the drawing beside what the model took off it

Page 1

crop

p01_r09

page 1 · bridge_deck_and_foundation_layout_p01_r09
Original
p01_r09
{
  "view": "Plan",
  "objects": [
    {
      "name": "Pier/Pier cap",
      "tag": "P1",
      "shape": "skewed rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "marked at top left, deck level plan side"
    },
    {
      "name": "Abutment",
      "tag": "A1",
      "shape": "skewed rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "marked at top right with centerline of expansion joint noted"
    },
    {
      "name": "RCC crash barrier",
      "tag": "",
      "shape": "linear rectangular",
      "material": "reinforced concrete",
      "count": 2,
      "note": "runs along both edges of deck in deck-level half plan"
    },
    {
      "name": "Pile / foundation element",
      "tag": "",
      "shape": "circular",
      "material": "reinforced concrete",
      "count": 18,
      "note": "shown as circles in foundation-level half plan, arranged in skewed grid rows"
    },
    {
      "name": "Deck slab girders/beams (shown as parallel lines)",
      "tag": "",
      "shape": "rectangular/tapered",
      "material": "reinforced concrete",
      "count": null,
      "note": "multiple parallel lines representing girder layout in deck-level plan"
    },
    {
      "name": "Expansion joint",
      "tag": "",
      "shape": "linear",
      "material": "",
      "count": 1,
      "note": "centerline of expansion joint noted near A1"
    },
    {
      "name": "Median/paved shoulder area",
      "tag": "",
      "shape": "trapezoidal",
      "material": "",
      "count": 1,
      "note": "partial label 'MEDI...P...' visible near right side, likely median or paved shoulder"
    },
    {
      "name": "Drainage/scupper symbols",
      "tag": "",
      "shape": "small square/diamond",
      "material": "",
      "count": 6,
      "note": "symbols along bottom edge of deck-level plan, possibly weep holes or drain spouts"
    }
  ],
  "measurements": [
    {
      "label": "Overall span (square)",
      "value": "40000",
      "unit": "",
      "appliesTo": "deck plan, P1 to A1"
    },
    {
      "label": "Overall span (skew)",
      "value": "46189",
      "unit": "",
      "appliesTo": "deck plan, P1 to A1"
    },
    {
      "label": "Offset at P1 (square)",
      "value": "1170",
      "unit": "",
      "appliesTo": "P1"
    },
    {
      "label": "Offset at P1 (skew)",
      "value": "1350",
      "unit": "",
      "appliesTo": "P1"
    },
    {
      "label": "Girder spacing",
      "value": "3500",
      "unit": "",
      "appliesTo": "deck level plan, repeated 4 times"
    },
    {
      "label": "Total width (deck level)",
      "value": "16550",
      "unit": "",
      "appliesTo": "deck level plan cross dimension"
    },
    {
      "label": "Offset (square) top",
      "value": "1275",
      "unit": "",
      "appliesTo": "deck level plan edge offset"
    },
    {
      "label": "Offset (square) bottom",
      "value": "1275",
      "unit": "",
      "appliesTo": "deck level plan edge offset"
    },
    {
      "label": "Skew angle",
      "value": "30",
      "unit": "degrees",
      "appliesTo": "deck geometry, skew callout"
    },
    {
      "label": "Barrier/beam spacing typical",
      "value": "5000",
      "unit": "",
      "appliesTo": "RCC crash barrier / beam spacing, typical"
    },
    {
      "label": "Pile spacing",
      "value": "3750",
      "unit": "",
      "appliesTo": "foundation level plan, repeated 4 times"
    },
    {
      "label": "Total width (foundation level)",
      "value": "16550",
      "unit": "",
      "appliesTo": "foundation level plan cross dimension"
    },
    {
      "label": "Offset (foundation level) top",
      "value": "775",
      "unit": "",
      "appliesTo": "foundation level plan edge offset"
    },
    {
      "label": "Offset (foundation level) bottom",
      "value": "775",
      "unit": "",
      "appliesTo": "foundation level plan edge offset"
    },
    {
      "label": "Scale",
      "value": "1:300",
      "unit": "",
      "appliesTo": "drawing scale"
    }
  ],
  "notes": [
    "HALF PLAN SHOWING DECK LEVEL",
    "HALF PLAN SHOWING FOUNDATION LEVEL",
    "(SCALE 1:300)",
    "30° SKEW",
    "5000 (TYP.)"
  ],
  "labels": [
    "P1",
    "A1",
    "TO KHANDWA",
    "C OF EXP. JOINT",
    "RCC CRASH BARRIER",
    "INDEPENDENT R... (partial, cut off)",
    "MEDI... P... (partial, cut off)"
  ],
  "description": "This crop shows two half-plan drawings of a skewed bridge span between pier P1 and abutment A1: the left half depicts the deck level with crash barriers, girder lines, and drainage symbols along a 30° skewed edge, while the right half shows the foundation level with a grid of circular pile marks at a skew, both plans dimensioned in millimeters with overall span, offsets, and spacing values. The drawing documents the deck layout and corresponding foundation/pile arrangement for a single span, including skew geometry and edge offsets, but does not show the full width of the bridge (only one half plan of each level is presented)."
}

p01_r09Plan

  • Pier/Pier capP1×1skewed rectangularreinforced concretemarked at top left, deck level plan side

40000 Overall span (square)46189 Overall span (skew)1170 Offset at P1 (square)1350 Offset at P1 (skew)3500 Girder spacing16550 Total width (deck level)1275 Offset (square) top1275 Offset (square) bottom+7 more

Page 2

crop

p02_r10

page 2 · bridge_pier_and_foundation_p02_r10
Original
p02_r10
{
  "view": "Cross Section",
  "objects": [
    {
      "name": "Pier",
      "tag": "P1",
      "shape": "column, circular in elevation (rectangular cap)",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Labelled RCC COLUMN PIER, shown as single circular/cylindrical shaft below pier cap"
    },
    {
      "name": "Pier cap / bearing pedestal",
      "tag": "",
      "shape": "rectangular, stepped",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Supports bearings, dimensioned 1500 depth split into 750+750"
    },
    {
      "name": "Crash barrier",
      "tag": "",
      "shape": "rectangular profile",
      "material": "reinforced concrete",
      "count": 2,
      "note": "RCC CRASH BARRIER at each edge of deck, 230 height shown both sides"
    },
    {
      "name": "PSC Girder",
      "tag": "",
      "shape": "I-girder (tapered flange, shown in section as vertical hatched webs)",
      "material": "precast concrete",
      "count": 2,
      "note": "PRECAST PSC GIRDER (TYP.), one on each side of pier centerline"
    },
    {
      "name": "Bearing",
      "tag": "",
      "shape": "rectangular, pot type",
      "material": "elastomeric/PTFE composite",
      "count": 4,
      "note": "POT-PTFE BEARING (TYP.), two pairs shown symmetric about centerline"
    },
    {
      "name": "Seismic stopper",
      "tag": "",
      "shape": "rectangular block",
      "material": "reinforced concrete",
      "count": 2,
      "note": "RCC SEISMIC STOPPER shown at bearing locations"
    },
    {
      "name": "Deck continuity slab/joint",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "DECK CONTINUITY labelled at top center over pier"
    },
    {
      "name": "Pile cap",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "RCC PILECAP, dashed outline, depth 1800"
    },
    {
      "name": "Bored cast-in-situ pile",
      "tag": "",
      "shape": "circular",
      "material": "reinforced concrete",
      "count": 2,
      "note": "1200 DIA BORED CAST-IN-SITU PILES, shown in section with hooked reinforcement ends"
    }
  ],
  "measurements": [
    {
      "label": "Distance from centerline to bearing",
      "value": "1170",
      "unit": "",
      "appliesTo": "square span layout"
    },
    {
      "label": "Distance from centerline to bearing (skew)",
      "value": "1350",
      "unit": "",
      "appliesTo": "skew span layout"
    },
    {
      "label": "Bearing gap at centerline of pier",
      "value": "1500",
      "unit": "",
      "appliesTo": "skew (SK) dimension between bearings"
    },
    {
      "label": "Crash barrier height",
      "value": "230",
      "unit": "",
      "appliesTo": "RCC crash barrier, both sides"
    },
    {
      "label": "Girder depth",
      "value": "2650",
      "unit": "",
      "appliesTo": "PRECAST PSC GIRDER, both sides"
    },
    {
      "label": "Pier cap total depth",
      "value": "1500",
      "unit": "",
      "appliesTo": "pier cap"
    },
    {
      "label": "Pier cap depth split (upper)",
      "value": "750",
      "unit": "",
      "appliesTo": "pier cap"
    },
    {
      "label": "Pier cap depth split (lower)",
      "value": "750",
      "unit": "",
      "appliesTo": "pier cap"
    },
    {
      "label": "Pier cap width square",
      "value": "3640",
      "unit": "",
      "appliesTo": "pier cap (SQ)"
    },
    {
      "label": "Pier cap width skew",
      "value": "4203",
      "unit": "",
      "appliesTo": "pier cap (SK)"
    },
    {
      "label": "Pier shaft width",
      "value": "1500",
      "unit": "",
      "appliesTo": "RCC column pier"
    },
    {
      "label": "Pile cap depth",
      "value": "1800",
      "unit": "",
      "appliesTo": "RCC pilecap"
    },
    {
      "label": "Edge distance from pile to pile cap edge",
      "value": "750",
      "unit": "",
      "appliesTo": "pile cap, both sides"
    },
    {
      "label": "Pile spacing center to center",
      "value": "3600",
      "unit": "",
      "appliesTo": "between piles"
    },
    {
      "label": "Total pile cap width",
      "value": "5100",
      "unit": "",
      "appliesTo": "pile cap"
    },
    {
      "label": "Pile diameter",
      "value": "1200",
      "unit": "DIA",
      "appliesTo": "bored cast-in-situ piles"
    }
  ],
  "notes": [],
  "labels": [
    "P1",
    "℄ OF BRG.",
    "FRL",
    "RCC CRASH BARRIER",
    "DECK CONTINUITY",
    "PRECAST PSC GIRDER (TYP.)",
    "RCC SEISMIC STOPPER",
    "POT-PTFE BEARING (TYP.)",
    "RCC COLUMN PIER",
    "RCC PILECAP",
    "1200 DIA BORED CAST-IN-SITU PILES",
    "SECTION P-P"
  ],
  "description": "This crop is a cross section through bridge pier P1, showing the deck/girder arrangement, pot-PTFE bearings with seismic stoppers atop a stepped pier cap, a single circular RCC column pier shaft, and below-ground an RCC pile cap supported on two 1200mm diameter bored cast-in-situ piles. It documents the substructure geometry and key dimensions (bearing spacing, pier cap and shaft sizes, pile cap depth, pile spacing) for pier P1, distinguishing square (SQ) and skew (SK) dimensions where the bridge is skewed.  The section title 'SECTION P-P' appears partially cut off at the bottom edge."
}

p02_r10Cross Section

  • Pier cap / bearing pedestal×1rectangular, steppedreinforced concreteSupports bearings, dimensioned 1500 depth split into 750+750

1170 Distance from centerline to bearing1350 Distance from centerline to bearing (skew)1500 Bearing gap at centerline of pier230 Crash barrier height2650 Girder depth1500 Pier cap total depth750 Pier cap depth split (upper)750 Pier cap depth split (lower)+8 more

crop

pier_p1

page 2 · pier_p1
Original
pier_p1
{
  "view": "Section",
  "objects": [
    {
      "name": "Pier",
      "tag": "P1",
      "shape": "",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Overall pier assembly shown in Section B-B, including cap, column, pile cap and piles"
    },
    {
      "name": "RCC crash barrier",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 2,
      "note": "Shown at deck edges, height 230 dimensioned"
    },
    {
      "name": "Deck slab / deck continuity",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Continuity joint at centerline of bridge"
    },
    {
      "name": "Precast PSC girder",
      "tag": "TYP.",
      "shape": "tapered/I-section (hatched)",
      "material": "precast concrete",
      "count": 2,
      "note": "Shown both sides of pier, depth 2650"
    },
    {
      "name": "Pot-PTFE bearing",
      "tag": "TYP.",
      "shape": "rectangular",
      "material": "",
      "count": 2,
      "note": "Located atop pier cap under girders"
    },
    {
      "name": "RCC seismic stopper",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Centered on pier cap between bearings"
    },
    {
      "name": "Pier cap / pier head",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Overall plan dimension 3640(SQ)/4203(SK), height 1500 split into two 750 segments"
    },
    {
      "name": "RCC column pier",
      "tag": "",
      "shape": "rectangular with chamfered corners",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Width 1500 shown in elevation; cross-section 1500x1000 with 25x25 chamfer shown separately"
    },
    {
      "name": "RCC pile cap",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Depth 1800, length 5100 (3600 between piles + 750 each side)"
    },
    {
      "name": "Bored cast-in-situ pile",
      "tag": "",
      "shape": "circular",
      "material": "reinforced concrete",
      "count": 2,
      "note": "1200 mm diameter piles under pile cap"
    }
  ],
  "measurements": [
    {
      "label": "Distance to bearing centerline (SQ)",
      "value": "1170",
      "unit": "",
      "appliesTo": "pier cap/bearing layout"
    },
    {
      "label": "Distance to bearing centerline (SK)",
      "value": "1350",
      "unit": "",
      "appliesTo": "pier cap/bearing layout"
    },
    {
      "label": "Crash barrier height",
      "value": "230",
      "unit": "",
      "appliesTo": "RCC crash barrier"
    },
    {
      "label": "Girder depth",
      "value": "2650",
      "unit": "",
      "appliesTo": "Precast PSC girder"
    },
    {
      "label": "Seismic stopper/bearing gap width (SK)",
      "value": "1500",
      "unit": "",
      "appliesTo": "RCC seismic stopper / pier cap"
    },
    {
      "label": "Pier cap height segment",
      "value": "750",
      "unit": "",
      "appliesTo": "Pier cap"
    },
    {
      "label": "Pier cap height segment (second)",
      "value": "750",
      "unit": "",
      "appliesTo": "Pier cap"
    },
    {
      "label": "Pier cap total height",
      "value": "1500",
      "unit": "",
      "appliesTo": "Pier cap"
    },
    {
      "label": "Pier cap plan dimension (SQ)",
      "value": "3640",
      "unit": "",
      "appliesTo": "Pier cap"
    },
    {
      "label": "Pier cap plan dimension (SK)",
      "value": "4203",
      "unit": "",
      "appliesTo": "Pier cap"
    },
    {
      "label": "Column width",
      "value": "1500",
      "unit": "",
      "appliesTo": "RCC column pier"
    },
    {
      "label": "Pile cap depth",
      "value": "1800",
      "unit": "",
      "appliesTo": "RCC pile cap"
    },
    {
      "label": "Distance between piles",
      "value": "3600",
      "unit": "",
      "appliesTo": "RCC pile cap"
    },
    {
      "label": "Edge distance to pile",
      "value": "750",
      "unit": "",
      "appliesTo": "RCC pile cap"
    },
    {
      "label": "Pile cap total length",
      "value": "5100",
      "unit": "",
      "appliesTo": "RCC pile cap"
    },
    {
      "label": "Pile diameter",
      "value": "1200",
      "unit": "",
      "appliesTo": "Bored cast-in-situ piles"
    },
    {
      "label": "Section width",
      "value": "1500",
      "unit": "",
      "appliesTo": "Section at pier location"
    },
    {
      "label": "Section depth",
      "value": "1000",
      "unit": "",
      "appliesTo": "Section at pier location"
    },
    {
      "label": "Chamfer size",
      "value": "25",
      "unit": "",
      "appliesTo": "Section at pier location (chamfer)"
    },
    {
      "label": "Chamfer size (second dimension)",
      "value": "25",
      "unit": "",
      "appliesTo": "Section at pier location (chamfer)"
    },
    {
      "label": "Scale of Section B-B",
      "value": "1:150",
      "unit": "",
      "appliesTo": "Section B-B"
    },
    {
      "label": "Scale of Section at Pier Location",
      "value": "1:25",
      "unit": "",
      "appliesTo": "Section at pier location"
    }
  ],
  "notes": [],
  "labels": [
    "P1",
    "℄ OF BRG.",
    "RCC CRASH BARRIER",
    "FRL",
    "DECK CONTINUITY",
    "PRECAST PSC GIRDER (TYP.)",
    "POT-PTFE BEARING (TYP.)",
    "RCC SEISMIC STOPPER",
    "RCC COLUMN PIER",
    "RCC PILECAP",
    "1200 DIA BORED CAST-IN-SITU PILES",
    "SECTION B-B",
    "(SCALE 1:150)",
    "SECTION AT PIER LOCATION",
    "(SCALE 1:25)",
    "CHAMFER 25X25"
  ],
  "description": "This crop shows two related structural sections for pier P1: a full-height Section B-B through the pier (from deck bearings down through the pier cap, column, pile cap and two bored piles) and a separate detail 'Section at Pier Location' showing the pier column's cross-sectional shape with chamfered corners. Dimensions cover crash barrier and girder depths, bearing spacing, pier cap and column sizes, pile cap dimensions, and pile diameter, documenting the concrete substructure elements supporting the superstructure at this pier."
}

pier_p1Section

  • Pier cap / pier head×1rectangularreinforced concreteOverall plan dimension 3640(SQ)/4203(SK), height 1500 split into two 750 segments

1170 Distance to bearing centerline (SQ)1350 Distance to bearing centerline (SK)230 Crash barrier height2650 Girder depth1500 Seismic stopper/bearing gap width (SK)750 Pier cap height segment750 Pier cap height segment (second)1500 Pier cap total height+14 more

crop

p02_r09 section b b

page 2 · structural_drawings_pkg_1_890ff33d80e843ef8aa5a52a7a9de3d8_p02_r09_section_b_b
Original
p02_r09 section b b
{
  "view": "Cross Section",
  "objects": [
    {
      "name": "Pier cap / pier bearing seat",
      "tag": "P1",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Cap supporting bearings and seismic stopper, shown at top of column pier"
    },
    {
      "name": "RCC crash barrier",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 2,
      "note": "Shown atop deck on both sides"
    },
    {
      "name": "Precast PSC girder",
      "tag": "",
      "shape": "tapered/I-section (haunched)",
      "material": "precast concrete",
      "count": 2,
      "note": "Typical girder either side of pier centerline"
    },
    {
      "name": "Deck slab with deck continuity joint",
      "tag": "",
      "shape": "flat slab",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Continuity over pier"
    },
    {
      "name": "Pot-PTFE bearing",
      "tag": "",
      "shape": "rectangular",
      "material": "elastomeric/PTFE composite",
      "count": 2,
      "note": "Typical bearing, one per girder line"
    },
    {
      "name": "RCC seismic stopper",
      "tag": "",
      "shape": "rectangular block",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Located between bearings at pier cap"
    },
    {
      "name": "RCC column pier",
      "tag": "",
      "shape": "rectangular/circular column",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Single column shaft below pier cap"
    },
    {
      "name": "RCC pile cap",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": ""
    },
    {
      "name": "Bored cast-in-situ pile",
      "tag": "",
      "shape": "circular",
      "material": "reinforced concrete",
      "count": 2,
      "note": "1200 dia piles shown in section, part of larger group"
    },
    {
      "name": "Chamfer detail",
      "tag": "SECTION A",
      "shape": "rectangular with chamfered corner",
      "material": "concrete",
      "count": 1,
      "note": "Shown in adjacent small detail, partially cropped"
    }
  ],
  "measurements": [
    {
      "label": "Distance from bearing centerline to edge (SQ)",
      "value": "1170",
      "unit": "mm",
      "appliesTo": "deck/pier cap"
    },
    {
      "label": "Distance from bearing centerline to edge (SK)",
      "value": "1350",
      "unit": "mm",
      "appliesTo": "deck/pier cap"
    },
    {
      "label": "Barrier height",
      "value": "230",
      "unit": "mm",
      "appliesTo": "RCC crash barrier"
    },
    {
      "label": "Girder depth",
      "value": "2650",
      "unit": "mm",
      "appliesTo": "Precast PSC girder"
    },
    {
      "label": "Bearing seat width (SK)",
      "value": "1500",
      "unit": "mm",
      "appliesTo": "pier cap/bearing area"
    },
    {
      "label": "Pier cap layer thickness",
      "value": "750",
      "unit": "mm",
      "appliesTo": "pier cap"
    },
    {
      "label": "Pier cap layer thickness",
      "value": "750",
      "unit": "mm",
      "appliesTo": "pier cap"
    },
    {
      "label": "Total pier cap depth",
      "value": "1500",
      "unit": "mm",
      "appliesTo": "pier cap"
    },
    {
      "label": "Pier cap width (SQ)",
      "value": "3640",
      "unit": "mm",
      "appliesTo": "pier cap"
    },
    {
      "label": "Pier cap width (SK)",
      "value": "4203",
      "unit": "mm",
      "appliesTo": "pier cap"
    },
    {
      "label": "Column width",
      "value": "1500",
      "unit": "mm",
      "appliesTo": "RCC column pier"
    },
    {
      "label": "Pile cap thickness",
      "value": "1800",
      "unit": "mm",
      "appliesTo": "RCC pile cap"
    },
    {
      "label": "Edge distance to pile",
      "value": "750",
      "unit": "mm",
      "appliesTo": "pile cap"
    },
    {
      "label": "Pile spacing",
      "value": "3600",
      "unit": "mm",
      "appliesTo": "piles"
    },
    {
      "label": "Overall pile cap width",
      "value": "5100",
      "unit": "mm",
      "appliesTo": "pile cap"
    },
    {
      "label": "Edge distance to pile",
      "value": "750",
      "unit": "mm",
      "appliesTo": "pile cap"
    },
    {
      "label": "Pile diameter",
      "value": "1200",
      "unit": "mm",
      "appliesTo": "bored cast-in-situ piles"
    },
    {
      "label": "Chamfer dimension",
      "value": "25",
      "unit": "mm",
      "appliesTo": "Section A chamfer detail"
    },
    {
      "label": "Chamfer dimension",
      "value": "25",
      "unit": "mm",
      "appliesTo": "Section A chamfer detail"
    },
    {
      "label": "Scale",
      "value": "1:150",
      "unit": "",
      "appliesTo": "Section B-B"
    }
  ],
  "notes": [
    "RCC CRASH BARRIER",
    "FRL",
    "DECK CONTINUITY",
    "PRECAST PSC GIRDER (TYP.)",
    "RCC SEISMIC STOPPER",
    "POT-PTFE BEARING (TYP.)",
    "RCC COLUMN PIER",
    "RCC PILECAP",
    "1200 DIA BORED CAST-IN-SITU PILES",
    "CHAMFER"
  ],
  "labels": [
    "P1",
    "C OF BRG.",
    "SECTION A",
    "SECTION B-B",
    "(SCALE 1:150)",
    "(SC..."
  ],
  "description": "This crop shows Section B-B, a cross section through a bridge pier (P1) at scale 1:150, illustrating the deck, PSC girders, crash barriers, pot-PTFE bearings, seismic stopper, pier cap, RCC column pier, pile cap, and two of the bored cast-in-situ piles with their spacing dimensions. A partial adjacent detail labeled 'SECTION A' shows a chamfer detail at a concrete edge, cut off at the right margin of the crop."
}

p02_r09 section b bCross Section

  • Pier cap / pier bearing seatP1×1rectangularreinforced concreteCap supporting bearings and seismic stopper, shown at top of column pier

1170 mm Distance from bearing centerline to edge (SQ)1350 mm Distance from bearing centerline to edge (SK)230 mm Barrier height2650 mm Girder depth1500 mm Bearing seat width (SK)750 mm Pier cap layer thickness750 mm Pier cap layer thickness1500 mm Total pier cap depth+12 more

crop

p02_r10 section b b

page 2 · structural_drawings_pkg_1_890ff33d80e843ef8aa5a52a7a9de3d8_p02_r10_section_b_b
Original
p02_r10 section b b
{
  "view": "Elevation",
  "objects": [
    {
      "name": "Crash Barrier",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 2,
      "note": "labeled RCC CRASH BARRIER, on either side of deck"
    },
    {
      "name": "PSC Girder",
      "tag": "",
      "shape": "I-girder/tapered",
      "material": "precast concrete",
      "count": 2,
      "note": "labeled PRECAST PSC GIRDER (TYP.), shown schematically hatched"
    },
    {
      "name": "Deck Continuity Slab",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "deck continuity at pier top"
    },
    {
      "name": "Bearing",
      "tag": "",
      "shape": "rectangular",
      "material": "",
      "count": 2,
      "note": "POT-PTFE BEARING (TYP.)"
    },
    {
      "name": "Seismic Stopper",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "RCC SEISMIC STOPPER, hatched block at pier cap top"
    },
    {
      "name": "Pier Cap",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "cap supporting bearings above column"
    },
    {
      "name": "Column Pier",
      "tag": "P1",
      "shape": "circular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "labeled RCC COLUMN PIER"
    },
    {
      "name": "Pile Cap",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "labeled RCC PILECAP, shown dashed (below ground/hidden)"
    },
    {
      "name": "Bored Cast-in-situ Pile",
      "tag": "",
      "shape": "circular",
      "material": "reinforced concrete",
      "count": 2,
      "note": "labeled 1200 DIA BORED CAST-IN-SITU PILES, shown dashed"
    }
  ],
  "measurements": [
    {
      "label": "Barrier width offset",
      "value": "230",
      "unit": "",
      "appliesTo": "Crash Barrier (each side)"
    },
    {
      "label": "Girder depth",
      "value": "2650",
      "unit": "",
      "appliesTo": "PSC Girder"
    },
    {
      "label": "Bearing spacing (square)",
      "value": "1170(SQ)",
      "unit": "",
      "appliesTo": "C OF BRG. spacing left"
    },
    {
      "label": "Bearing spacing (skew)",
      "value": "1350(SK)",
      "unit": "",
      "appliesTo": "C OF BRG. spacing left"
    },
    {
      "label": "Bearing spacing (square)",
      "value": "1170(SQ)",
      "unit": "",
      "appliesTo": "C OF BRG. spacing right"
    },
    {
      "label": "Bearing spacing (skew)",
      "value": "1350(SK)",
      "unit": "",
      "appliesTo": "C OF BRG. spacing right"
    },
    {
      "label": "Seismic stopper width (skew)",
      "value": "1500(SK)",
      "unit": "",
      "appliesTo": "RCC Seismic Stopper"
    },
    {
      "label": "Pier cap depth upper",
      "value": "750",
      "unit": "",
      "appliesTo": "Pier Cap"
    },
    {
      "label": "Pier cap depth lower",
      "value": "750",
      "unit": "",
      "appliesTo": "Pier Cap"
    },
    {
      "label": "Pier cap total depth",
      "value": "1500",
      "unit": "",
      "appliesTo": "Pier Cap"
    },
    {
      "label": "Pier cap width (square)",
      "value": "3640(SQ)",
      "unit": "",
      "appliesTo": "Pier Cap"
    },
    {
      "label": "Pier cap width (skew)",
      "value": "4203(SK)",
      "unit": "",
      "appliesTo": "Pier Cap"
    },
    {
      "label": "Column diameter",
      "value": "1500",
      "unit": "",
      "appliesTo": "Column Pier P1"
    },
    {
      "label": "Pile cap depth",
      "value": "1800",
      "unit": "",
      "appliesTo": "Pile Cap"
    },
    {
      "label": "Pile edge distance left",
      "value": "750",
      "unit": "",
      "appliesTo": "Pile Cap"
    },
    {
      "label": "Pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "Bored Piles"
    },
    {
      "label": "Pile edge distance right",
      "value": "750",
      "unit": "",
      "appliesTo": "Pile Cap"
    },
    {
      "label": "Pile cap overall width",
      "value": "5100",
      "unit": "",
      "appliesTo": "Pile Cap"
    },
    {
      "label": "Pile diameter",
      "value": "1200",
      "unit": "DIA",
      "appliesTo": "Bored Cast-in-situ Piles"
    }
  ],
  "notes": [
    "RCC CRASH BARRIER",
    "FRL",
    "DECK CONTINUITY",
    "RCC SEISMIC STOPPER",
    "POT-PTFE BEARING (TYP.)",
    "PRECAST PSC GIRDER (TYP.)",
    "RCC COLUMN PIER",
    "RCC PILECAP",
    "1200 DIA BORED CAST-IN-SITU PILES"
  ],
  "labels": [
    "P1",
    "C OF BRG."
  ],
  "description": "This crop is an elevation view of a bridge pier (marked P1) showing the deck cross-section above with crash barriers, precast PSC girders, deck continuity slab, pot-PTFE bearings and seismic stopper, resting on a pier cap supported by a single circular RCC column pier. Below ground, the column continues to a pile cap (shown dashed/hidden) founded on two 1200mm diameter bored cast-in-situ piles. Key dimensions for bearing spacing, pier cap size (square and skew), column diameter, pile cap dimensions, and pile spacing are annotated."
}

p02_r10 section b bElevation

  • Pier Cap×1rectangularreinforced concretecap supporting bearings above column

230 Barrier width offset2650 Girder depth1170(SQ) Bearing spacing (square)1350(SK) Bearing spacing (skew)1170(SQ) Bearing spacing (square)1350(SK) Bearing spacing (skew)1500(SK) Seismic stopper width (skew)750 Pier cap depth upper+11 more

crop

p02_r13 section at pier location

page 2 · structural_drawings_pkg_1_890ff33d80e843ef8aa5a52a7a9de3d8_p02_r13_section_at_pier_location
Original
p02_r13 section at pier location
{
  "view": "Section",
  "objects": [
    {
      "name": "Section element at pier location (likely girder/beam or pier cap cross-section)",
      "tag": "",
      "shape": "rectangular with chamfered corners",
      "material": "",
      "count": 1,
      "note": "Chamfer detail 25x25 shown at top-left corner; likely representative of all four corners"
    }
  ],
  "measurements": [
    {
      "label": "Width",
      "value": "1500",
      "unit": "",
      "appliesTo": "Section at pier location"
    },
    {
      "label": "Height",
      "value": "1000",
      "unit": "",
      "appliesTo": "Section at pier location"
    },
    {
      "label": "Chamfer dimension",
      "value": "25",
      "unit": "",
      "appliesTo": "corner chamfer"
    },
    {
      "label": "Chamfer size",
      "value": "25X25",
      "unit": "",
      "appliesTo": "corner chamfer"
    },
    {
      "label": "Scale",
      "value": "1:25",
      "unit": "",
      "appliesTo": "drawing scale"
    }
  ],
  "notes": [
    "CHAMFER 25X25"
  ],
  "labels": [
    "SECTION AT PIER LOCATION",
    "(SCALE 1:25)"
  ],
  "description": "This crop shows a cross-section labeled 'SECTION AT PIER LOCATION' at scale 1:25, depicting a rectangular member measuring 1500 by 1000 (units not stated, likely mm) with 25x25 chamfers at the corners. No reinforcement, material callout, or additional context is shown in this fragment beyond the outline and dimensions."
}

p02_r13 section at pier locationSection

  • Section element at pier location (likely girder/beam or pier cap cross-section)×1rectangular with chamfered cornersChamfer detail 25x25 shown at top-left corner; likely representative of all four corners

1500 Width1000 Height25 Chamfer dimension25X25 Chamfer size1:25 Scale

Page 3

crop

p03_r02 cross section of deck and pile cap at pier p1

page 3 · structural_drawings_pkg_1_890ff33d80e843ef8aa5a52a7a9de3d8_p03_r02_cross_section_of_deck_and_pile_cap_at_pier_p1
Original
p03_r02 cross section of deck and pile cap at pier p1
{
  "view": "Cross Section",
  "objects": [
    {
      "name": "Deck slab (RCC cast in situ)",
      "tag": "",
      "shape": "slab, cambered/tapered top",
      "material": "reinforced concrete",
      "count": 2,
      "note": "One deck shown for each carriageway (L/S and R/S), separated by median gap at CL of proposed road"
    },
    {
      "name": "Wearing course",
      "tag": "WC",
      "shape": "layer, sloped 2.5%",
      "material": "bituminous/asphalt (implied)",
      "count": 2,
      "note": "50mm thick, shown over deck slab each side"
    },
    {
      "name": "RCC crash barrier",
      "tag": "",
      "shape": "tapered rectangular",
      "material": "reinforced concrete",
      "count": 2,
      "note": "At outer edges of each carriageway"
    },
    {
      "name": "Footpath",
      "tag": "",
      "shape": "rectangular strip",
      "material": "",
      "count": 2,
      "note": "1500mm wide footpath each side, between carriageway and crash barrier"
    },
    {
      "name": "Pier cap / pile cap top and bottom levels (PCTL/PCBL)",
      "tag": "P1",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 2,
      "note": "Shown for L/S and R/S of Pier P1; levels marked PCTL and PCBL"
    },
    {
      "name": "Pier columns/webs (square)",
      "tag": "",
      "shape": "square (SQ) columns",
      "material": "reinforced concrete",
      "count": 10,
      "note": "Dimensioned as 1275(SQ) and 3500(SQ) sections spanning 16550mm width, per pier row, two rows shown (L/S & R/S)"
    },
    {
      "name": "Piles",
      "tag": "P1",
      "shape": "circular",
      "material": "reinforced concrete",
      "count": 10,
      "note": "Shown below pile cap, 5 piles per side (L/S and R/S), spaced at 3000mm typical with 775mm end offsets"
    },
    {
      "name": "Abutment section (partial, cropped)",
      "tag": "A1 & A2",
      "shape": "not fully visible",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Only top dimension line (775-16550-775) and pile tip levels visible; main section body cropped out of view above"
    }
  ],
  "measurements": [
    {
      "label": "Width dimension",
      "value": "775",
      "unit": "mm",
      "appliesTo": "Abutment section (partial, top)"
    },
    {
      "label": "Width dimension",
      "value": "16550",
      "unit": "mm",
      "appliesTo": "Abutment section / Pier section overall width"
    },
    {
      "label": "Width dimension",
      "value": "775",
      "unit": "mm",
      "appliesTo": "Abutment section (partial, top)"
    },
    {
      "label": "Pile tip level",
      "value": "481.905",
      "unit": "",
      "appliesTo": "A1 L/S"
    },
    {
      "label": "Pile tip level",
      "value": "484.641",
      "unit": "",
      "appliesTo": "A2 L/S"
    },
    {
      "label": "Pile tip level",
      "value": "481.905",
      "unit": "",
      "appliesTo": "A1 R/S"
    },
    {
      "label": "Pile tip level",
      "value": "484.641",
      "unit": "",
      "appliesTo": "A2 R/S"
    },
    {
      "label": "Scale",
      "value": "1:150",
      "unit": "",
      "appliesTo": "Section at Abutment Location at A1 & A2"
    },
    {
      "label": "Carriageway width",
      "value": "13500",
      "unit": "mm",
      "appliesTo": "LHS carriageway"
    },
    {
      "label": "Carriageway width",
      "value": "13500",
      "unit": "mm",
      "appliesTo": "RHS carriageway"
    },
    {
      "label": "Median/gap dimension",
      "value": "2900",
      "unit": "mm",
      "appliesTo": "CL of proposed road gap between carriageways"
    },
    {
      "label": "Footpath width",
      "value": "1500",
      "unit": "mm",
      "appliesTo": "Footpath (each side)"
    },
    {
      "label": "Crash barrier/edge dimension",
      "value": "450",
      "unit": "mm",
      "appliesTo": "Crash barrier / edge strip"
    },
    {
      "label": "Deck edge dimension",
      "value": "100",
      "unit": "mm",
      "appliesTo": "Deck edge thickness/step"
    },
    {
      "label": "Wearing course thickness",
      "value": "50",
      "unit": "mm",
      "appliesTo": "RCC cast in situ deck WC layer"
    },
    {
      "label": "Slope",
      "value": "2.5",
      "unit": "%",
      "appliesTo": "Deck cross slope"
    },
    {
      "label": "Dimension",
      "value": "750",
      "unit": "mm",
      "appliesTo": "Deck/girder detail near crash barrier"
    },
    {
      "label": "Overall width",
      "value": "16550",
      "unit": "mm",
      "appliesTo": "Pier cap/pile cap width"
    },
    {
      "label": "Column/pier width",
      "value": "1275",
      "unit": "mm",
      "appliesTo": "Pier column (SQ) end segment"
    },
    {
      "label": "Column/pier width",
      "value": "3500",
      "unit": "mm",
      "appliesTo": "Pier column (SQ) segments (x4)"
    },
    {
      "label": "Spacing dimension",
      "value": "1000",
      "unit": "mm",
      "appliesTo": "Pile/pier spacing end offset"
    },
    {
      "label": "Spacing dimension",
      "value": "4500",
      "unit": "mm",
      "appliesTo": "Pile/pier spacing (x2)"
    },
    {
      "label": "Pier cap top level",
      "value": "515.384",
      "unit": "",
      "appliesTo": "PCTL P1 L/S"
    },
    {
      "label": "Pier cap top level",
      "value": "515.567",
      "unit": "",
      "appliesTo": "PCTL A2 R/S (as printed)"
    },
    {
      "label": "Level",
      "value": "503.316",
      "unit": "",
      "appliesTo": "PCTL P1 L/S (as printed)"
    },
    {
      "label": "Level",
      "value": "503.316",
      "unit": "",
      "appliesTo": "PCTL P1 R/S (as printed)"
    },
    {
      "label": "Pile cap bottom level",
      "value": "501.516",
      "unit": "",
      "appliesTo": "PCBL P1 L/S"
    },
    {
      "label": "Pile cap bottom level",
      "value": "501.516",
      "unit": "",
      "appliesTo": "PCBL P1 R/S"
    },
    {
      "label": "Pile tip level",
      "value": "476.566",
      "unit": "",
      "appliesTo": "Pile P1 L/S"
    },
    {
      "label": "Pile tip level",
      "value": "476.566",
      "unit": "",
      "appliesTo": "Pile P1 R/S"
    },
    {
      "label": "Pile spacing",
      "value": "3000",
      "unit": "mm",
      "appliesTo": "Piles under P1 (x4 spacings each side)"
    },
    {
      "label": "End offset",
      "value": "775",
      "unit": "mm",
      "appliesTo": "Pile group end offset each side"
    },
    {
      "label": "Overall width",
      "value": "16550",
      "unit": "mm",
      "appliesTo": "Pile group total width"
    },
    {
      "label": "Scale",
      "value": "1:150",
      "unit": "",
      "appliesTo": "Section at Pier Location"
    }
  ],
  "notes": [
    "READ THIS DRAWING IN CONJUNCTION WITH OTHER SHEETS OF THE SAME DRAWING NUMBER"
  ],
  "labels": [
    "SECTION AT ABUTMENT LOCATION AT A1 & A2",
    "SECTION AT PIER LOCATION",
    "CL OF PROPOSED ROAD",
    "CL OF LHS (CARRIAGEWAY)",
    "CL OF RHS (CARRIAGEWAY)",
    "FRL",
    "FOOTPATH",
    "RCC CRASH BARRIER",
    "RCC CAST IN SITU DECK",
    "50mm THK. (WC)",
    "NOTES:",
    "DESIGN CONSULTANT: LEA ASSOCIATES SOUTH ASIA PVT. LTD.",
    "B-1, E-27, IInd FLOOR, MOHAN COOPERATIVE INDUSTRIAL ESTATE, MATHURA ROAD, NEW DELHI-110044",
    "CLIENT: NATIONAL HIGHWAYS AUTHORITY OF INDIA (Ministry of Road Transport & Highways) Government of India",
    "DRAWING TITLE: GENERAL ARRANGEMENT DRAWING FOR MAJOR BRIDGE AT CH. 64+412",
    "DRG. NO.: 73580A\\LASA\\STR\\MJBR5\\GA-01",
    "REV: R0",
    "SCALE: AS SHOWN",
    "DATE: DEC.2025",
    "DRAWN: KUNAL",
    "PROJECT: DEVELOPMENT OF 6 LANE GREENFIELD ACCESS CONTROLLED INDORE EASTERN BYPASS STARTING FROM DESIGN KM 64+... (partial, cut off)"
  ],
  "description": "This crop shows two typical cross sections of a major bridge: an abutment section at A1 & A2 (mostly cropped out, only the top dimension line 775-16550-775 and pile tip levels remain visible) and a fully detailed pier section (Section at Pier Location) showing twin carriageways with footpaths, RCC crash barriers, RCC cast-in-situ deck with 50mm wearing course sloped at 2.5%, pier cap (PCTL/PCBL) levels, square pier columns, and a group of circular piles with pile tip levels for Pier P1 on both L/S and R/S. The bottom title block identifies this as part of the General Arrangement Drawing for a major bridge at Ch. 64+412, prepared by LEA Associates South Asia for NHAI, Drawing No. 73580A\\LASA\\STR\\MJBR5\\GA-01, Rev R0."
}

p03_r02 cross section of deck and pile cap at pier p1Cross Section

  • Pier cap / pile cap top and bottom levels (PCTL/PCBL)P1×2rectangularreinforced concreteShown for L/S and R/S of Pier P1; levels marked PCTL and PCBL
  • PilesP1×10circularreinforced concreteShown below pile cap, 5 piles per side (L/S and R/S), spaced at 3000mm typical with 775mm end offsets

775 mm Width dimension16550 mm Width dimension775 mm Width dimension481.905 Pile tip level484.641 Pile tip level481.905 Pile tip level484.641 Pile tip level1:150 Scale+26 more