Drawing → BOQ
← Mindmapwhat the drawings said

Seismic Stopper

1 page · 8 crops · ×9 · substructure

Matched toSeismic Restrainerbridge.substructure.seismic_restraineron “RCC Seismic Stopper”

1 read off the drawings · 1 derived · 3 not established
The class asks forValueHowFrom
LengthLwants m/mmnot establishedThe seismic stopper is only labeled/located in the sections (adjacent to bearing at abutment A2, centrally over pier cap at P1) but no explicit length dimension is called out for it.not found
WidthWwants m/mmnot establishedAll width-type dimensions in these crops (e.g., pier cap width 3640/4203, bearing seat 1500, column width 1500) are explicitly attributed to other elements, not the seismic stopper.not found
HeightHwants m/mmnot establishedVertical dimensions present (2650 girder depth, 230 crash barrier/deck thickness, 1500 pedestal height) are all explicitly tied to other named elements (girder, crash barrier, bearing pedestal), not the seismic stopper.not found
Instance CountNwants count2 countReadings show one RCC Seismic Stopper adjacent to the bearing at abutment A2 (crops abutment_and_approach_slab_p02_r11, abutment_retaining_wall_and_piles_p02_r08, structural_drawings...r11_section_a_a) and one centrally over the pier cap at pier P1 (crops bridge_pier_and_foundation_p02_r10, pier_p1, structural_drawings...r09_section_b_b, structural_drawings...r10_section_b_b). Each location shows count=1 for the seismic stopper object. Total distinct locations documented = A2 + P1 = 2.The readings only document seismic stoppers at abutment A2 and pier P1; no other piers/abutments are shown in the given crops, so the count derivable from available data is 2. The actual bridge may have additional piers/abutments not captured in these crops, but that cannot be confirmed from the given readings.derivedcheckp2 · p02_r11p2 · p02_r10
Material TypeMATReinforced Cement Concrete (RCC) -Every crop labels the item as 'RCC SEISMIC STOPPER' and lists material as 'reinforced concrete' for the seismic stopper object.The material is explicitly and consistently stated as reinforced concrete (RCC) in every occurrence of the seismic stopper across all 8 crops.readp2 · p02_r11p2 · pier_p1

Worked out by anthropic/claude-sonnet-5 from the readings below, which are the source. A derived value shows its arithmetic — check it against the drawing before it is priced.

How the sheets named it

RCC seismic stopperRCC SEISMIC STOPPER

Every dimension read for it1

  • 1500(SK)Seismic stopper width (skew)p2 · p02_r10 section b b

Notes on the sheets that carry it

  • p2℄ OF EXP. JOINT
  • p2℄ OF BRG.
  • p2POT-PTFE BEARING (TYP.)
  • p2RCC SEISMIC STOPPER
  • p2STONE PITCHING
  • p2INDEPENDENT RE... (text cut off)
  • p2600 THK. FILTER ... (text cut off)
  • p21200 DIA BORED ... CAST-IN-SITU PILE ... (text cut off)
  • p2STONE PITCHIN(G) [partial]
  • p2INDEPENDENT F [partial, likely 'INDEPENDENT FOOTING' or similar]
  • p2600 THK. FILTE [partial, likely 'FILTER']
  • p21200 DIA BORED [partial]
  • p2CAST-IN-SITU PI [partial, likely 'PILE']
  • p2CL OF EXP. JOINT
  • p2CL OF BRG.
  • p2RCC CRASH BARRIER
  • p2FRL
  • p2DECK CONTINUITY
  • p2PRECAST PSC GIRDER (TYP.)
  • p2RCC COLUMN PIER
  • p2RCC PILECAP
  • p21200 DIA BORED CAST-IN-SITU PILES
  • p2CHAMFER
  • p2INDEPENDENT RETAINING WALL
  • p2600 THK. FILTER MEDIA

Every crop it was read in — the drawing beside what the model took off it

Page 2

crop

p02_r11

page 2 · abutment_and_approach_slab_p02_r11
Original
p02_r11
{
  "view": "Cross Section",
  "objects": [
    {
      "name": "Abutment",
      "tag": "A2",
      "shape": "rectangular with sloped backfill face",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Marked by circled tag 'A2' at top; centerline of bearing (₽ OF BRG.) and centerline of expansion joint (₽ OF EXP. JOINT) shown at abutment"
    },
    {
      "name": "Approach slab",
      "tag": "",
      "shape": "rectangular tapered/stepped",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Slab at top left with 1500 and 2850 sub-dimensions, adjacent to abutment cap"
    },
    {
      "name": "Bearing",
      "tag": "POT-PTFE BEARING (TYP.)",
      "shape": "rectangular block",
      "material": "not stated (typical elastomeric/PTFE bearing)",
      "count": 1,
      "note": "Located under girder seat, called out as typical"
    },
    {
      "name": "Seismic stopper",
      "tag": "RCC SEISMIC STOPPER",
      "shape": "rectangular block",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Adjacent to bearing"
    },
    {
      "name": "Bored cast-in-situ pile",
      "tag": "",
      "shape": "circular",
      "material": "reinforced concrete",
      "count": 4,
      "note": "Shown in dashed outline below abutment footing, spaced at 3600 c/c with 750 end offsets"
    },
    {
      "name": "Retaining wall",
      "tag": "INDEPENDENT RETAINING WALL",
      "shape": "vertical wall",
      "material": "not stated (likely reinforced concrete)",
      "count": 1,
      "note": "Shown as vertical line with dashed extent behind abutment"
    },
    {
      "name": "Stone pitching",
      "tag": "STONE PITCHING",
      "shape": "sloped surface layer",
      "material": "stone",
      "count": 1,
      "note": "Applied on sloped embankment face behind abutment"
    },
    {
      "name": "Filter media layer",
      "tag": "600 THK. FILTER MEDIA",
      "shape": "layer, hatched",
      "material": "granular filter material",
      "count": 1,
      "note": "Shown as hatched band along slope, 600 thick"
    },
    {
      "name": "Embankment/backfill",
      "tag": "",
      "shape": "sloped fill",
      "material": "earth/granular fill (hatched)",
      "count": 1,
      "note": "Sloped fill behind abutment with circular aggregate symbol"
    }
  ],
  "measurements": [
    {
      "label": "",
      "value": "1070",
      "unit": "",
      "appliesTo": "distance from ₽ of BRG to face, SQ (square) dimension"
    },
    {
      "label": "",
      "value": "1236",
      "unit": "",
      "appliesTo": "same location, SK (skew) dimension"
    },
    {
      "label": "EXP.GAP",
      "value": "80",
      "unit": "",
      "appliesTo": "expansion gap, SQ"
    },
    {
      "label": "EXP.GAP",
      "value": "92",
      "unit": "",
      "appliesTo": "expansion gap, SK"
    },
    {
      "label": "",
      "value": "230",
      "unit": "",
      "appliesTo": "deck/slab thickness at top left"
    },
    {
      "label": "",
      "value": "2650",
      "unit": "",
      "appliesTo": "vertical dimension at approach slab area"
    },
    {
      "label": "",
      "value": "1500",
      "unit": "",
      "appliesTo": "approach slab sub-dimension"
    },
    {
      "label": "",
      "value": "2850",
      "unit": "",
      "appliesTo": "approach slab sub-dimension"
    },
    {
      "label": "",
      "value": "3500",
      "unit": "",
      "appliesTo": "SQ dimension near girder seat"
    },
    {
      "label": "",
      "value": "1500",
      "unit": "",
      "appliesTo": "dimension along sloped face lower section"
    },
    {
      "label": "",
      "value": "750",
      "unit": "",
      "appliesTo": "end offset, left side of pile group"
    },
    {
      "label": "",
      "value": "3600",
      "unit": "",
      "appliesTo": "pile spacing c/c (repeated three times)"
    },
    {
      "label": "",
      "value": "750",
      "unit": "",
      "appliesTo": "end offset, right side of pile group"
    },
    {
      "label": "",
      "value": "12300",
      "unit": "",
      "appliesTo": "overall length across pile group"
    },
    {
      "label": "pile diameter",
      "value": "1200",
      "unit": "DIA",
      "appliesTo": "bored cast-in-situ piles"
    },
    {
      "label": "filter media thickness",
      "value": "600",
      "unit": "THK.",
      "appliesTo": "filter media layer"
    },
    {
      "label": "scale",
      "value": "1:150",
      "unit": "",
      "appliesTo": "SECTION A-A"
    }
  ],
  "notes": [],
  "labels": [
    "A2",
    "₽ OF EXP. JOINT",
    "₽ OF BRG.",
    "POT-PTFE BEARING (TYP.)",
    "RCC SEISMIC STOPPER",
    "STONE PITCHING",
    "INDEPENDENT RETAINING WALL",
    "600 THK. FILTER MEDIA",
    "1200 DIA BORED CAST-IN-SITU PILES",
    "SECTION A-A",
    "(SCALE 1:150)"
  ],
  "description": "This crop shows a cross section (SECTION A-A, scale 1:150) through abutment A2 of a bridge, detailing the approach slab, POT-PTFE bearing, RCC seismic stopper, expansion joint gap, sloped backfill with stone pitching and filter media, an independent retaining wall, and a row of four 1200mm diameter bored cast-in-situ piles spaced at 3600mm centers beneath the abutment. It documents the substructure detailing at the abutment including bearing seat dimensions, expansion gap, backfill treatment, and pile foundation layout."
}

p02_r11Cross Section

  • Seismic stopperRCC SEISMIC STOPPER×1rectangular blockreinforced concreteAdjacent to bearing

1070123680 EXP.GAP92 EXP.GAP230265015002850+9 more

crop

p02_r08

page 2 · abutment_retaining_wall_and_piles_p02_r08
Original
p02_r08
{
  "view": "Cross Section",
  "objects": [
    {
      "name": "Abutment",
      "tag": "A2",
      "shape": "tapered/trapezoidal stem with sloped backfill face",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Main abutment body shown with backfill, bearing shelf, and pile foundation below."
    },
    {
      "name": "Bearing",
      "tag": "",
      "shape": "rectangular",
      "material": "not stated (POT-PTFE type)",
      "count": 1,
      "note": "Labelled POT-PTFE BEARING (TYP.), located at abutment top near centerline of bearing."
    },
    {
      "name": "Seismic stopper",
      "tag": "",
      "shape": "rectangular block",
      "material": "reinforced concrete (RCC)",
      "count": 1,
      "note": "Labelled RCC SEISMIC STOPPER, adjacent to bearing."
    },
    {
      "name": "Bored cast-in-situ pile",
      "tag": "",
      "shape": "circular",
      "material": "reinforced concrete",
      "count": 4,
      "note": "Shown in plan-like footprint below abutment, spaced at 3600mm centers, 1200 dia (per partial label)."
    },
    {
      "name": "Stone pitching / slope protection",
      "tag": "",
      "shape": "irregular/graded stone fill",
      "material": "stone",
      "count": 1,
      "note": "Labelled STONE PITCHING on embankment slope."
    },
    {
      "name": "Filter media layer",
      "tag": "",
      "shape": "layer",
      "material": "granular fill",
      "count": 1,
      "note": "Labelled 600 THK. FILTER (text cut off), behind abutment stem."
    },
    {
      "name": "Expansion joint",
      "tag": "",
      "shape": "narrow gap",
      "material": "not stated",
      "count": 1,
      "note": "Located at deck top, labelled 80(SQ) 92(SK) EXP.GAP, aligned with ℄ OF EXP. JOINT."
    },
    {
      "name": "Deck/girder end (partial)",
      "tag": "",
      "shape": "rectangular",
      "material": "not stated",
      "count": 1,
      "note": "Only a small portion of the superstructure end near the bearing is visible."
    },
    {
      "name": "Approach embankment fill",
      "tag": "",
      "shape": "sloped/tapered wedge",
      "material": "earth/granular fill",
      "count": 1,
      "note": "Fill behind and below abutment, shown with hatching pattern."
    }
  ],
  "measurements": [
    {
      "label": "1070",
      "value": "1070",
      "unit": "mm",
      "appliesTo": "square dimension near ℄ OF BRG"
    },
    {
      "label": "1236",
      "value": "1236",
      "unit": "mm",
      "appliesTo": "skew dimension near ℄ OF BRG"
    },
    {
      "label": "80",
      "value": "80",
      "unit": "mm",
      "appliesTo": "expansion gap (square)"
    },
    {
      "label": "92",
      "value": "92",
      "unit": "mm",
      "appliesTo": "expansion gap (skew)"
    },
    {
      "label": "3500",
      "value": "3500",
      "unit": "mm",
      "appliesTo": "deck/abutment top dimension (SQ)"
    },
    {
      "label": "230",
      "value": "230",
      "unit": "mm",
      "appliesTo": "deck slab thickness at top of abutment"
    },
    {
      "label": "2650",
      "value": "2650",
      "unit": "mm",
      "appliesTo": "vertical dimension of abutment upper section"
    },
    {
      "label": "1500",
      "value": "1500",
      "unit": "mm",
      "appliesTo": "horizontal dimension of abutment backfill/seat"
    },
    {
      "label": "2850",
      "value": "2850",
      "unit": "mm",
      "appliesTo": "horizontal dimension adjacent to 1500 measurement"
    },
    {
      "label": "1500",
      "value": "1500",
      "unit": "mm",
      "appliesTo": "lower horizontal dimension near pile cap area"
    },
    {
      "label": "750",
      "value": "750",
      "unit": "mm",
      "appliesTo": "end spacing of pile group (left side)"
    },
    {
      "label": "3600",
      "value": "3600",
      "unit": "mm",
      "appliesTo": "pile spacing (three instances)"
    },
    {
      "label": "750",
      "value": "750",
      "unit": "mm",
      "appliesTo": "end spacing of pile group (right side)"
    },
    {
      "label": "12300",
      "value": "12300",
      "unit": "mm",
      "appliesTo": "overall pile group width"
    },
    {
      "label": "600 THK",
      "value": "600",
      "unit": "mm",
      "appliesTo": "filter layer thickness (label partially cut off)"
    },
    {
      "label": "1200 DIA",
      "value": "1200",
      "unit": "mm",
      "appliesTo": "bored cast-in-situ pile diameter (label partially cut off)"
    },
    {
      "label": "SCALE",
      "value": "1:150",
      "unit": "",
      "appliesTo": "SECTION A-A"
    }
  ],
  "notes": [
    "℄ OF EXP. JOINT",
    "℄ OF BRG.",
    "POT-PTFE BEARING (TYP.)",
    "RCC SEISMIC STOPPER",
    "STONE PITCHING",
    "INDEPENDENT RE... (text cut off)",
    "600 THK. FILTER ... (text cut off)",
    "1200 DIA BORED ... CAST-IN-SITU PILE ... (text cut off)"
  ],
  "labels": [
    "A2",
    "SECTION A-A",
    "(SCALE 1:150)"
  ],
  "description": "This crop is a cross section (Section A-A, scale 1:150) through abutment A2 of a bridge, showing the abutment stem, backfill, POT-PTFE bearing with RCC seismic stopper at the bearing shelf, and a row of four bored cast-in-situ piles beneath the abutment spaced at 3600mm centers with 750mm end offsets (overall 12300mm). Slope protection via stone pitching and a filter layer is shown on the embankment face, with partial superstructure and expansion joint details visible at the top of the section; some right-side callout text is cut off at the crop edge."
}

p02_r08Cross Section

  • Seismic stopper×1rectangular blockreinforced concrete (RCC)Labelled RCC SEISMIC STOPPER, adjacent to bearing.

1070 mm 10701236 mm 123680 mm 8092 mm 923500 mm 3500230 mm 2302650 mm 26501500 mm 1500+9 more

crop

p02_r10

page 2 · bridge_pier_and_foundation_p02_r10
Original
p02_r10
{
  "view": "Cross Section",
  "objects": [
    {
      "name": "Pier",
      "tag": "P1",
      "shape": "column, circular in elevation (rectangular cap)",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Labelled RCC COLUMN PIER, shown as single circular/cylindrical shaft below pier cap"
    },
    {
      "name": "Pier cap / bearing pedestal",
      "tag": "",
      "shape": "rectangular, stepped",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Supports bearings, dimensioned 1500 depth split into 750+750"
    },
    {
      "name": "Crash barrier",
      "tag": "",
      "shape": "rectangular profile",
      "material": "reinforced concrete",
      "count": 2,
      "note": "RCC CRASH BARRIER at each edge of deck, 230 height shown both sides"
    },
    {
      "name": "PSC Girder",
      "tag": "",
      "shape": "I-girder (tapered flange, shown in section as vertical hatched webs)",
      "material": "precast concrete",
      "count": 2,
      "note": "PRECAST PSC GIRDER (TYP.), one on each side of pier centerline"
    },
    {
      "name": "Bearing",
      "tag": "",
      "shape": "rectangular, pot type",
      "material": "elastomeric/PTFE composite",
      "count": 4,
      "note": "POT-PTFE BEARING (TYP.), two pairs shown symmetric about centerline"
    },
    {
      "name": "Seismic stopper",
      "tag": "",
      "shape": "rectangular block",
      "material": "reinforced concrete",
      "count": 2,
      "note": "RCC SEISMIC STOPPER shown at bearing locations"
    },
    {
      "name": "Deck continuity slab/joint",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "DECK CONTINUITY labelled at top center over pier"
    },
    {
      "name": "Pile cap",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "RCC PILECAP, dashed outline, depth 1800"
    },
    {
      "name": "Bored cast-in-situ pile",
      "tag": "",
      "shape": "circular",
      "material": "reinforced concrete",
      "count": 2,
      "note": "1200 DIA BORED CAST-IN-SITU PILES, shown in section with hooked reinforcement ends"
    }
  ],
  "measurements": [
    {
      "label": "Distance from centerline to bearing",
      "value": "1170",
      "unit": "",
      "appliesTo": "square span layout"
    },
    {
      "label": "Distance from centerline to bearing (skew)",
      "value": "1350",
      "unit": "",
      "appliesTo": "skew span layout"
    },
    {
      "label": "Bearing gap at centerline of pier",
      "value": "1500",
      "unit": "",
      "appliesTo": "skew (SK) dimension between bearings"
    },
    {
      "label": "Crash barrier height",
      "value": "230",
      "unit": "",
      "appliesTo": "RCC crash barrier, both sides"
    },
    {
      "label": "Girder depth",
      "value": "2650",
      "unit": "",
      "appliesTo": "PRECAST PSC GIRDER, both sides"
    },
    {
      "label": "Pier cap total depth",
      "value": "1500",
      "unit": "",
      "appliesTo": "pier cap"
    },
    {
      "label": "Pier cap depth split (upper)",
      "value": "750",
      "unit": "",
      "appliesTo": "pier cap"
    },
    {
      "label": "Pier cap depth split (lower)",
      "value": "750",
      "unit": "",
      "appliesTo": "pier cap"
    },
    {
      "label": "Pier cap width square",
      "value": "3640",
      "unit": "",
      "appliesTo": "pier cap (SQ)"
    },
    {
      "label": "Pier cap width skew",
      "value": "4203",
      "unit": "",
      "appliesTo": "pier cap (SK)"
    },
    {
      "label": "Pier shaft width",
      "value": "1500",
      "unit": "",
      "appliesTo": "RCC column pier"
    },
    {
      "label": "Pile cap depth",
      "value": "1800",
      "unit": "",
      "appliesTo": "RCC pilecap"
    },
    {
      "label": "Edge distance from pile to pile cap edge",
      "value": "750",
      "unit": "",
      "appliesTo": "pile cap, both sides"
    },
    {
      "label": "Pile spacing center to center",
      "value": "3600",
      "unit": "",
      "appliesTo": "between piles"
    },
    {
      "label": "Total pile cap width",
      "value": "5100",
      "unit": "",
      "appliesTo": "pile cap"
    },
    {
      "label": "Pile diameter",
      "value": "1200",
      "unit": "DIA",
      "appliesTo": "bored cast-in-situ piles"
    }
  ],
  "notes": [],
  "labels": [
    "P1",
    "℄ OF BRG.",
    "FRL",
    "RCC CRASH BARRIER",
    "DECK CONTINUITY",
    "PRECAST PSC GIRDER (TYP.)",
    "RCC SEISMIC STOPPER",
    "POT-PTFE BEARING (TYP.)",
    "RCC COLUMN PIER",
    "RCC PILECAP",
    "1200 DIA BORED CAST-IN-SITU PILES",
    "SECTION P-P"
  ],
  "description": "This crop is a cross section through bridge pier P1, showing the deck/girder arrangement, pot-PTFE bearings with seismic stoppers atop a stepped pier cap, a single circular RCC column pier shaft, and below-ground an RCC pile cap supported on two 1200mm diameter bored cast-in-situ piles. It documents the substructure geometry and key dimensions (bearing spacing, pier cap and shaft sizes, pile cap depth, pile spacing) for pier P1, distinguishing square (SQ) and skew (SK) dimensions where the bridge is skewed.  The section title 'SECTION P-P' appears partially cut off at the bottom edge."
}

p02_r10Cross Section

  • Seismic stopper×2rectangular blockreinforced concreteRCC SEISMIC STOPPER shown at bearing locations

1170 Distance from centerline to bearing1350 Distance from centerline to bearing (skew)1500 Bearing gap at centerline of pier230 Crash barrier height2650 Girder depth1500 Pier cap total depth750 Pier cap depth split (upper)750 Pier cap depth split (lower)+8 more

crop

pier_p1

page 2 · pier_p1
Original
pier_p1
{
  "view": "Section",
  "objects": [
    {
      "name": "Pier",
      "tag": "P1",
      "shape": "",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Overall pier assembly shown in Section B-B, including cap, column, pile cap and piles"
    },
    {
      "name": "RCC crash barrier",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 2,
      "note": "Shown at deck edges, height 230 dimensioned"
    },
    {
      "name": "Deck slab / deck continuity",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Continuity joint at centerline of bridge"
    },
    {
      "name": "Precast PSC girder",
      "tag": "TYP.",
      "shape": "tapered/I-section (hatched)",
      "material": "precast concrete",
      "count": 2,
      "note": "Shown both sides of pier, depth 2650"
    },
    {
      "name": "Pot-PTFE bearing",
      "tag": "TYP.",
      "shape": "rectangular",
      "material": "",
      "count": 2,
      "note": "Located atop pier cap under girders"
    },
    {
      "name": "RCC seismic stopper",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Centered on pier cap between bearings"
    },
    {
      "name": "Pier cap / pier head",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Overall plan dimension 3640(SQ)/4203(SK), height 1500 split into two 750 segments"
    },
    {
      "name": "RCC column pier",
      "tag": "",
      "shape": "rectangular with chamfered corners",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Width 1500 shown in elevation; cross-section 1500x1000 with 25x25 chamfer shown separately"
    },
    {
      "name": "RCC pile cap",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Depth 1800, length 5100 (3600 between piles + 750 each side)"
    },
    {
      "name": "Bored cast-in-situ pile",
      "tag": "",
      "shape": "circular",
      "material": "reinforced concrete",
      "count": 2,
      "note": "1200 mm diameter piles under pile cap"
    }
  ],
  "measurements": [
    {
      "label": "Distance to bearing centerline (SQ)",
      "value": "1170",
      "unit": "",
      "appliesTo": "pier cap/bearing layout"
    },
    {
      "label": "Distance to bearing centerline (SK)",
      "value": "1350",
      "unit": "",
      "appliesTo": "pier cap/bearing layout"
    },
    {
      "label": "Crash barrier height",
      "value": "230",
      "unit": "",
      "appliesTo": "RCC crash barrier"
    },
    {
      "label": "Girder depth",
      "value": "2650",
      "unit": "",
      "appliesTo": "Precast PSC girder"
    },
    {
      "label": "Seismic stopper/bearing gap width (SK)",
      "value": "1500",
      "unit": "",
      "appliesTo": "RCC seismic stopper / pier cap"
    },
    {
      "label": "Pier cap height segment",
      "value": "750",
      "unit": "",
      "appliesTo": "Pier cap"
    },
    {
      "label": "Pier cap height segment (second)",
      "value": "750",
      "unit": "",
      "appliesTo": "Pier cap"
    },
    {
      "label": "Pier cap total height",
      "value": "1500",
      "unit": "",
      "appliesTo": "Pier cap"
    },
    {
      "label": "Pier cap plan dimension (SQ)",
      "value": "3640",
      "unit": "",
      "appliesTo": "Pier cap"
    },
    {
      "label": "Pier cap plan dimension (SK)",
      "value": "4203",
      "unit": "",
      "appliesTo": "Pier cap"
    },
    {
      "label": "Column width",
      "value": "1500",
      "unit": "",
      "appliesTo": "RCC column pier"
    },
    {
      "label": "Pile cap depth",
      "value": "1800",
      "unit": "",
      "appliesTo": "RCC pile cap"
    },
    {
      "label": "Distance between piles",
      "value": "3600",
      "unit": "",
      "appliesTo": "RCC pile cap"
    },
    {
      "label": "Edge distance to pile",
      "value": "750",
      "unit": "",
      "appliesTo": "RCC pile cap"
    },
    {
      "label": "Pile cap total length",
      "value": "5100",
      "unit": "",
      "appliesTo": "RCC pile cap"
    },
    {
      "label": "Pile diameter",
      "value": "1200",
      "unit": "",
      "appliesTo": "Bored cast-in-situ piles"
    },
    {
      "label": "Section width",
      "value": "1500",
      "unit": "",
      "appliesTo": "Section at pier location"
    },
    {
      "label": "Section depth",
      "value": "1000",
      "unit": "",
      "appliesTo": "Section at pier location"
    },
    {
      "label": "Chamfer size",
      "value": "25",
      "unit": "",
      "appliesTo": "Section at pier location (chamfer)"
    },
    {
      "label": "Chamfer size (second dimension)",
      "value": "25",
      "unit": "",
      "appliesTo": "Section at pier location (chamfer)"
    },
    {
      "label": "Scale of Section B-B",
      "value": "1:150",
      "unit": "",
      "appliesTo": "Section B-B"
    },
    {
      "label": "Scale of Section at Pier Location",
      "value": "1:25",
      "unit": "",
      "appliesTo": "Section at pier location"
    }
  ],
  "notes": [],
  "labels": [
    "P1",
    "℄ OF BRG.",
    "RCC CRASH BARRIER",
    "FRL",
    "DECK CONTINUITY",
    "PRECAST PSC GIRDER (TYP.)",
    "POT-PTFE BEARING (TYP.)",
    "RCC SEISMIC STOPPER",
    "RCC COLUMN PIER",
    "RCC PILECAP",
    "1200 DIA BORED CAST-IN-SITU PILES",
    "SECTION B-B",
    "(SCALE 1:150)",
    "SECTION AT PIER LOCATION",
    "(SCALE 1:25)",
    "CHAMFER 25X25"
  ],
  "description": "This crop shows two related structural sections for pier P1: a full-height Section B-B through the pier (from deck bearings down through the pier cap, column, pile cap and two bored piles) and a separate detail 'Section at Pier Location' showing the pier column's cross-sectional shape with chamfered corners. Dimensions cover crash barrier and girder depths, bearing spacing, pier cap and column sizes, pile cap dimensions, and pile diameter, documenting the concrete substructure elements supporting the superstructure at this pier."
}

pier_p1Section

  • RCC seismic stopper×1rectangularreinforced concreteCentered on pier cap between bearings

1170 Distance to bearing centerline (SQ)1350 Distance to bearing centerline (SK)230 Crash barrier height2650 Girder depth1500 Seismic stopper/bearing gap width (SK)750 Pier cap height segment750 Pier cap height segment (second)1500 Pier cap total height+14 more

crop

p02_r08 abutment section with retaining wall and bored piles

page 2 · structural_drawings_pkg_1_890ff33d80e843ef8aa5a52a7a9de3d8_p02_r08_abutment_section_with_retaining_wall_and_bored_piles
Original
p02_r08 abutment section with retaining wall and bored piles
{
  "view": "Section",
  "objects": [
    {
      "name": "Abutment",
      "tag": "A2",
      "shape": "tapered/trapezoidal",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Abutment section with sloped back face and seismic stopper"
    },
    {
      "name": "Bearing",
      "tag": "",
      "shape": "rectangular",
      "material": "POT-PTFE",
      "count": 1,
      "note": "Labeled POT-PTFE BEARING (TYP.), located at abutment top"
    },
    {
      "name": "Seismic Stopper",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Labeled RCC SEISMIC STOPPER"
    },
    {
      "name": "Expansion Joint",
      "tag": "",
      "shape": "linear gap",
      "material": "",
      "count": 1,
      "note": "Centerline of expansion joint shown with gap dimension"
    },
    {
      "name": "Pile",
      "tag": "",
      "shape": "circular",
      "material": "cast-in-situ concrete",
      "count": 4,
      "note": "1200 dia bored cast-in-situ piles, shown in dashed elevation below abutment"
    },
    {
      "name": "Filter Layer",
      "tag": "",
      "shape": "",
      "material": "granular filter",
      "count": 1,
      "note": "600 THK. FILTER (partial label) shown near ground level"
    },
    {
      "name": "Stone Pitching",
      "tag": "",
      "shape": "",
      "material": "stone",
      "count": 1,
      "note": "STONE PITCHIN(G) label, partial text, embankment slope protection"
    },
    {
      "name": "Approach Embankment/Slope Fill",
      "tag": "",
      "shape": "tapered",
      "material": "granular fill",
      "count": 1,
      "note": "Hatched fill material forming approach slope behind abutment"
    },
    {
      "name": "Wing Wall/Return",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Small stepped concrete element near top left, partially visible with break line"
    }
  ],
  "measurements": [
    {
      "label": "Distance from CL BRG to CL EXP JOINT (SQ)",
      "value": "1070",
      "unit": "",
      "appliesTo": "A2 abutment"
    },
    {
      "label": "Distance from CL BRG to CL EXP JOINT (SK)",
      "value": "1236",
      "unit": "",
      "appliesTo": "A2 abutment"
    },
    {
      "label": "Expansion gap (SQ)",
      "value": "80",
      "unit": "",
      "appliesTo": "expansion joint"
    },
    {
      "label": "Expansion gap (SK)",
      "value": "92",
      "unit": "",
      "appliesTo": "expansion joint"
    },
    {
      "label": "Width dimension",
      "value": "3500",
      "unit": "",
      "appliesTo": "top slab/deck near abutment"
    },
    {
      "label": "Vertical dimension",
      "value": "230",
      "unit": "",
      "appliesTo": "deck/slab thickness at top"
    },
    {
      "label": "Vertical dimension",
      "value": "2650",
      "unit": "",
      "appliesTo": "abutment stem height"
    },
    {
      "label": "Horizontal dimension",
      "value": "1500",
      "unit": "",
      "appliesTo": "abutment top step"
    },
    {
      "label": "Horizontal dimension",
      "value": "2850",
      "unit": "",
      "appliesTo": "abutment top area"
    },
    {
      "label": "Horizontal dimension",
      "value": "1500",
      "unit": "",
      "appliesTo": "lower abutment/slope area"
    },
    {
      "label": "Pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "piles"
    },
    {
      "label": "Pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "piles"
    },
    {
      "label": "Pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "piles"
    },
    {
      "label": "Edge distance",
      "value": "750",
      "unit": "",
      "appliesTo": "pile group left edge"
    },
    {
      "label": "Edge distance",
      "value": "750",
      "unit": "",
      "appliesTo": "pile group right edge"
    },
    {
      "label": "Total pile group width",
      "value": "12300",
      "unit": "",
      "appliesTo": "pile group"
    },
    {
      "label": "Pile diameter",
      "value": "1200",
      "unit": "DIA",
      "appliesTo": "bored cast-in-situ piles"
    },
    {
      "label": "Filter thickness",
      "value": "600",
      "unit": "THK",
      "appliesTo": "filter layer"
    },
    {
      "label": "Scale",
      "value": "1:150",
      "unit": "",
      "appliesTo": "Section A-A"
    }
  ],
  "notes": [
    "POT-PTFE BEARING (TYP.)",
    "RCC SEISMIC STOPPER",
    "STONE PITCHIN(G) [partial]",
    "INDEPENDENT F [partial, likely 'INDEPENDENT FOOTING' or similar]",
    "600 THK. FILTE [partial, likely 'FILTER']",
    "1200 DIA BORED [partial]",
    "CAST-IN-SITU PI [partial, likely 'PILE']",
    "CL OF EXP. JOINT",
    "CL OF BRG."
  ],
  "labels": [
    "A2",
    "SECTION A-A",
    "(SCALE 1:150)"
  ],
  "description": "This crop shows a cross-section (Section A-A) through abutment A2 of a bridge, illustrating the abutment stem, bearing arrangement (POT-PTFE bearing with RCC seismic stopper), expansion joint gap dimensions for square and skew geometries, backfill and slope protection details, and a row of four bored cast-in-situ piles with spacing dimensions below the abutment. It documents structural and geometric details needed for abutment, bearing, and foundation pile quantities."
}

p02_r08 abutment section with retaining wall and bored pilesSection

  • Seismic Stopper×1rectangularreinforced concreteLabeled RCC SEISMIC STOPPER

1070 Distance from CL BRG to CL EXP JOINT (SQ)1236 Distance from CL BRG to CL EXP JOINT (SK)80 Expansion gap (SQ)92 Expansion gap (SK)3500 Width dimension230 Vertical dimension2650 Vertical dimension1500 Horizontal dimension+11 more

crop

p02_r09 section b b

page 2 · structural_drawings_pkg_1_890ff33d80e843ef8aa5a52a7a9de3d8_p02_r09_section_b_b
Original
p02_r09 section b b
{
  "view": "Cross Section",
  "objects": [
    {
      "name": "Pier cap / pier bearing seat",
      "tag": "P1",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Cap supporting bearings and seismic stopper, shown at top of column pier"
    },
    {
      "name": "RCC crash barrier",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 2,
      "note": "Shown atop deck on both sides"
    },
    {
      "name": "Precast PSC girder",
      "tag": "",
      "shape": "tapered/I-section (haunched)",
      "material": "precast concrete",
      "count": 2,
      "note": "Typical girder either side of pier centerline"
    },
    {
      "name": "Deck slab with deck continuity joint",
      "tag": "",
      "shape": "flat slab",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Continuity over pier"
    },
    {
      "name": "Pot-PTFE bearing",
      "tag": "",
      "shape": "rectangular",
      "material": "elastomeric/PTFE composite",
      "count": 2,
      "note": "Typical bearing, one per girder line"
    },
    {
      "name": "RCC seismic stopper",
      "tag": "",
      "shape": "rectangular block",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Located between bearings at pier cap"
    },
    {
      "name": "RCC column pier",
      "tag": "",
      "shape": "rectangular/circular column",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Single column shaft below pier cap"
    },
    {
      "name": "RCC pile cap",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": ""
    },
    {
      "name": "Bored cast-in-situ pile",
      "tag": "",
      "shape": "circular",
      "material": "reinforced concrete",
      "count": 2,
      "note": "1200 dia piles shown in section, part of larger group"
    },
    {
      "name": "Chamfer detail",
      "tag": "SECTION A",
      "shape": "rectangular with chamfered corner",
      "material": "concrete",
      "count": 1,
      "note": "Shown in adjacent small detail, partially cropped"
    }
  ],
  "measurements": [
    {
      "label": "Distance from bearing centerline to edge (SQ)",
      "value": "1170",
      "unit": "mm",
      "appliesTo": "deck/pier cap"
    },
    {
      "label": "Distance from bearing centerline to edge (SK)",
      "value": "1350",
      "unit": "mm",
      "appliesTo": "deck/pier cap"
    },
    {
      "label": "Barrier height",
      "value": "230",
      "unit": "mm",
      "appliesTo": "RCC crash barrier"
    },
    {
      "label": "Girder depth",
      "value": "2650",
      "unit": "mm",
      "appliesTo": "Precast PSC girder"
    },
    {
      "label": "Bearing seat width (SK)",
      "value": "1500",
      "unit": "mm",
      "appliesTo": "pier cap/bearing area"
    },
    {
      "label": "Pier cap layer thickness",
      "value": "750",
      "unit": "mm",
      "appliesTo": "pier cap"
    },
    {
      "label": "Pier cap layer thickness",
      "value": "750",
      "unit": "mm",
      "appliesTo": "pier cap"
    },
    {
      "label": "Total pier cap depth",
      "value": "1500",
      "unit": "mm",
      "appliesTo": "pier cap"
    },
    {
      "label": "Pier cap width (SQ)",
      "value": "3640",
      "unit": "mm",
      "appliesTo": "pier cap"
    },
    {
      "label": "Pier cap width (SK)",
      "value": "4203",
      "unit": "mm",
      "appliesTo": "pier cap"
    },
    {
      "label": "Column width",
      "value": "1500",
      "unit": "mm",
      "appliesTo": "RCC column pier"
    },
    {
      "label": "Pile cap thickness",
      "value": "1800",
      "unit": "mm",
      "appliesTo": "RCC pile cap"
    },
    {
      "label": "Edge distance to pile",
      "value": "750",
      "unit": "mm",
      "appliesTo": "pile cap"
    },
    {
      "label": "Pile spacing",
      "value": "3600",
      "unit": "mm",
      "appliesTo": "piles"
    },
    {
      "label": "Overall pile cap width",
      "value": "5100",
      "unit": "mm",
      "appliesTo": "pile cap"
    },
    {
      "label": "Edge distance to pile",
      "value": "750",
      "unit": "mm",
      "appliesTo": "pile cap"
    },
    {
      "label": "Pile diameter",
      "value": "1200",
      "unit": "mm",
      "appliesTo": "bored cast-in-situ piles"
    },
    {
      "label": "Chamfer dimension",
      "value": "25",
      "unit": "mm",
      "appliesTo": "Section A chamfer detail"
    },
    {
      "label": "Chamfer dimension",
      "value": "25",
      "unit": "mm",
      "appliesTo": "Section A chamfer detail"
    },
    {
      "label": "Scale",
      "value": "1:150",
      "unit": "",
      "appliesTo": "Section B-B"
    }
  ],
  "notes": [
    "RCC CRASH BARRIER",
    "FRL",
    "DECK CONTINUITY",
    "PRECAST PSC GIRDER (TYP.)",
    "RCC SEISMIC STOPPER",
    "POT-PTFE BEARING (TYP.)",
    "RCC COLUMN PIER",
    "RCC PILECAP",
    "1200 DIA BORED CAST-IN-SITU PILES",
    "CHAMFER"
  ],
  "labels": [
    "P1",
    "C OF BRG.",
    "SECTION A",
    "SECTION B-B",
    "(SCALE 1:150)",
    "(SC..."
  ],
  "description": "This crop shows Section B-B, a cross section through a bridge pier (P1) at scale 1:150, illustrating the deck, PSC girders, crash barriers, pot-PTFE bearings, seismic stopper, pier cap, RCC column pier, pile cap, and two of the bored cast-in-situ piles with their spacing dimensions. A partial adjacent detail labeled 'SECTION A' shows a chamfer detail at a concrete edge, cut off at the right margin of the crop."
}

p02_r09 section b bCross Section

  • RCC seismic stopper×1rectangular blockreinforced concreteLocated between bearings at pier cap

1170 mm Distance from bearing centerline to edge (SQ)1350 mm Distance from bearing centerline to edge (SK)230 mm Barrier height2650 mm Girder depth1500 mm Bearing seat width (SK)750 mm Pier cap layer thickness750 mm Pier cap layer thickness1500 mm Total pier cap depth+12 more

crop

p02_r10 section b b

page 2 · structural_drawings_pkg_1_890ff33d80e843ef8aa5a52a7a9de3d8_p02_r10_section_b_b
Original
p02_r10 section b b
{
  "view": "Elevation",
  "objects": [
    {
      "name": "Crash Barrier",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 2,
      "note": "labeled RCC CRASH BARRIER, on either side of deck"
    },
    {
      "name": "PSC Girder",
      "tag": "",
      "shape": "I-girder/tapered",
      "material": "precast concrete",
      "count": 2,
      "note": "labeled PRECAST PSC GIRDER (TYP.), shown schematically hatched"
    },
    {
      "name": "Deck Continuity Slab",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "deck continuity at pier top"
    },
    {
      "name": "Bearing",
      "tag": "",
      "shape": "rectangular",
      "material": "",
      "count": 2,
      "note": "POT-PTFE BEARING (TYP.)"
    },
    {
      "name": "Seismic Stopper",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "RCC SEISMIC STOPPER, hatched block at pier cap top"
    },
    {
      "name": "Pier Cap",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "cap supporting bearings above column"
    },
    {
      "name": "Column Pier",
      "tag": "P1",
      "shape": "circular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "labeled RCC COLUMN PIER"
    },
    {
      "name": "Pile Cap",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "labeled RCC PILECAP, shown dashed (below ground/hidden)"
    },
    {
      "name": "Bored Cast-in-situ Pile",
      "tag": "",
      "shape": "circular",
      "material": "reinforced concrete",
      "count": 2,
      "note": "labeled 1200 DIA BORED CAST-IN-SITU PILES, shown dashed"
    }
  ],
  "measurements": [
    {
      "label": "Barrier width offset",
      "value": "230",
      "unit": "",
      "appliesTo": "Crash Barrier (each side)"
    },
    {
      "label": "Girder depth",
      "value": "2650",
      "unit": "",
      "appliesTo": "PSC Girder"
    },
    {
      "label": "Bearing spacing (square)",
      "value": "1170(SQ)",
      "unit": "",
      "appliesTo": "C OF BRG. spacing left"
    },
    {
      "label": "Bearing spacing (skew)",
      "value": "1350(SK)",
      "unit": "",
      "appliesTo": "C OF BRG. spacing left"
    },
    {
      "label": "Bearing spacing (square)",
      "value": "1170(SQ)",
      "unit": "",
      "appliesTo": "C OF BRG. spacing right"
    },
    {
      "label": "Bearing spacing (skew)",
      "value": "1350(SK)",
      "unit": "",
      "appliesTo": "C OF BRG. spacing right"
    },
    {
      "label": "Seismic stopper width (skew)",
      "value": "1500(SK)",
      "unit": "",
      "appliesTo": "RCC Seismic Stopper"
    },
    {
      "label": "Pier cap depth upper",
      "value": "750",
      "unit": "",
      "appliesTo": "Pier Cap"
    },
    {
      "label": "Pier cap depth lower",
      "value": "750",
      "unit": "",
      "appliesTo": "Pier Cap"
    },
    {
      "label": "Pier cap total depth",
      "value": "1500",
      "unit": "",
      "appliesTo": "Pier Cap"
    },
    {
      "label": "Pier cap width (square)",
      "value": "3640(SQ)",
      "unit": "",
      "appliesTo": "Pier Cap"
    },
    {
      "label": "Pier cap width (skew)",
      "value": "4203(SK)",
      "unit": "",
      "appliesTo": "Pier Cap"
    },
    {
      "label": "Column diameter",
      "value": "1500",
      "unit": "",
      "appliesTo": "Column Pier P1"
    },
    {
      "label": "Pile cap depth",
      "value": "1800",
      "unit": "",
      "appliesTo": "Pile Cap"
    },
    {
      "label": "Pile edge distance left",
      "value": "750",
      "unit": "",
      "appliesTo": "Pile Cap"
    },
    {
      "label": "Pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "Bored Piles"
    },
    {
      "label": "Pile edge distance right",
      "value": "750",
      "unit": "",
      "appliesTo": "Pile Cap"
    },
    {
      "label": "Pile cap overall width",
      "value": "5100",
      "unit": "",
      "appliesTo": "Pile Cap"
    },
    {
      "label": "Pile diameter",
      "value": "1200",
      "unit": "DIA",
      "appliesTo": "Bored Cast-in-situ Piles"
    }
  ],
  "notes": [
    "RCC CRASH BARRIER",
    "FRL",
    "DECK CONTINUITY",
    "RCC SEISMIC STOPPER",
    "POT-PTFE BEARING (TYP.)",
    "PRECAST PSC GIRDER (TYP.)",
    "RCC COLUMN PIER",
    "RCC PILECAP",
    "1200 DIA BORED CAST-IN-SITU PILES"
  ],
  "labels": [
    "P1",
    "C OF BRG."
  ],
  "description": "This crop is an elevation view of a bridge pier (marked P1) showing the deck cross-section above with crash barriers, precast PSC girders, deck continuity slab, pot-PTFE bearings and seismic stopper, resting on a pier cap supported by a single circular RCC column pier. Below ground, the column continues to a pile cap (shown dashed/hidden) founded on two 1200mm diameter bored cast-in-situ piles. Key dimensions for bearing spacing, pier cap size (square and skew), column diameter, pile cap dimensions, and pile spacing are annotated."
}

p02_r10 section b bElevation

  • Seismic Stopper×1rectangularreinforced concreteRCC SEISMIC STOPPER, hatched block at pier cap top

230 Barrier width offset2650 Girder depth1170(SQ) Bearing spacing (square)1350(SK) Bearing spacing (skew)1170(SQ) Bearing spacing (square)1350(SK) Bearing spacing (skew)1500(SK) Seismic stopper width (skew)750 Pier cap depth upper+11 more

crop

p02_r11 section a a

page 2 · structural_drawings_pkg_1_890ff33d80e843ef8aa5a52a7a9de3d8_p02_r11_section_a_a
Original
p02_r11 section a a
{
  "view": "Section",
  "objects": [
    {
      "name": "Abutment",
      "tag": "A2",
      "shape": "tapered/battered",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Abutment with backwall supporting bearing seat, shown with sloped face against embankment"
    },
    {
      "name": "Bearing",
      "tag": "",
      "shape": "rectangular",
      "material": "PTFE/elastomeric (Pot-PTFE)",
      "count": 1,
      "note": "Labeled POT-PTFE BEARING (TYP.), seated on abutment cap"
    },
    {
      "name": "Seismic Stopper",
      "tag": "",
      "shape": "rectangular block",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Labeled RCC SEISMIC STOPPER, adjacent to bearing"
    },
    {
      "name": "Expansion Joint",
      "tag": "",
      "shape": "linear gap",
      "material": "",
      "count": 1,
      "note": "Located at centerline of exp. joint, gap dimensions given as 80(SQ)/92(SK)"
    },
    {
      "name": "Deck/Girder",
      "tag": "",
      "shape": "rectangular slab with haunch",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Top slab shown with 230 thickness dimension and 3500(SQ) span reference"
    },
    {
      "name": "Retaining Wall",
      "tag": "",
      "shape": "vertical wall",
      "material": "reinforced concrete (implied)",
      "count": 1,
      "note": "Labeled INDEPENDENT RETAINING WALL, separate from abutment"
    },
    {
      "name": "Pile",
      "tag": "",
      "shape": "circular",
      "material": "cast-in-situ concrete",
      "count": 4,
      "note": "Labeled 1200 DIA BORED CAST-IN-SITU PILES, shown in elevation/plan strip below section, 4 piles visible with spacing"
    },
    {
      "name": "Stone Pitching",
      "tag": "",
      "shape": "sloped layer",
      "material": "stone",
      "count": 1,
      "note": "Labeled STONE PITCHING on embankment slope"
    },
    {
      "name": "Filter Media",
      "tag": "",
      "shape": "layer",
      "material": "granular fill",
      "count": 1,
      "note": "Labeled 600 THK. FILTER MEDIA behind retaining wall"
    },
    {
      "name": "Embankment/Backfill",
      "tag": "",
      "shape": "sloped fill",
      "material": "earth/granular",
      "count": 1,
      "note": "Shown with hatching, sloped approach fill behind abutment"
    },
    {
      "name": "Ground Line",
      "tag": "",
      "shape": "irregular line",
      "material": "",
      "count": 1,
      "note": "Existing ground surface shown with break line at far right"
    }
  ],
  "measurements": [
    {
      "label": "",
      "value": "1070",
      "unit": "mm",
      "appliesTo": "distance from bearing CL to exp. joint CL, square case (SQ)"
    },
    {
      "label": "",
      "value": "1236",
      "unit": "mm",
      "appliesTo": "distance from bearing CL to exp. joint CL, skew case (SK)"
    },
    {
      "label": "",
      "value": "80",
      "unit": "mm",
      "appliesTo": "expansion gap, square case (SQ)"
    },
    {
      "label": "",
      "value": "92",
      "unit": "mm",
      "appliesTo": "expansion gap, skew case (SK), labeled EXP.GAP"
    },
    {
      "label": "",
      "value": "230",
      "unit": "mm",
      "appliesTo": "deck slab thickness"
    },
    {
      "label": "",
      "value": "3500",
      "unit": "mm",
      "appliesTo": "span/offset dimension (SQ) at deck level"
    },
    {
      "label": "",
      "value": "2650",
      "unit": "mm",
      "appliesTo": "vertical dimension, abutment section height"
    },
    {
      "label": "",
      "value": "1500",
      "unit": "mm",
      "appliesTo": "horizontal dimension near bearing seat"
    },
    {
      "label": "",
      "value": "2850",
      "unit": "mm",
      "appliesTo": "horizontal dimension near bearing seat"
    },
    {
      "label": "",
      "value": "1500",
      "unit": "mm",
      "appliesTo": "horizontal offset dimension near retaining wall base"
    },
    {
      "label": "",
      "value": "750",
      "unit": "mm",
      "appliesTo": "pile spacing, edge distance (left)"
    },
    {
      "label": "",
      "value": "3600",
      "unit": "mm",
      "appliesTo": "pile spacing (x3)"
    },
    {
      "label": "",
      "value": "750",
      "unit": "mm",
      "appliesTo": "pile spacing, edge distance (right)"
    },
    {
      "label": "",
      "value": "12300",
      "unit": "mm",
      "appliesTo": "total pile group width"
    },
    {
      "label": "",
      "value": "600",
      "unit": "mm",
      "appliesTo": "filter media thickness"
    },
    {
      "label": "",
      "value": "1200",
      "unit": "mm",
      "appliesTo": "pile diameter"
    },
    {
      "label": "1:150",
      "value": "1:150",
      "unit": "",
      "appliesTo": "drawing scale"
    }
  ],
  "notes": [
    "POT-PTFE BEARING (TYP.)",
    "RCC SEISMIC STOPPER",
    "STONE PITCHING",
    "INDEPENDENT RETAINING WALL",
    "600 THK. FILTER MEDIA",
    "1200 DIA BORED CAST-IN-SITU PILES"
  ],
  "labels": [
    "A2",
    "C OF EXP. JOINT",
    "C OF BRG.",
    "SECTION A-A",
    "(SCALE 1:150)"
  ],
  "description": "This crop shows a cross-section (Section A-A) through abutment A2 of a bridge, detailing the bearing arrangement, seismic stopper, expansion joint gap dimensions for square and skew conditions, the sloped embankment fill with stone pitching, an independent retaining wall with filter media, and a row of four 1200mm diameter bored cast-in-situ piles with their spacing dimensions. It documents the abutment structural detail, foundation piling layout, and associated earthwork/retaining elements at this location."
}

p02_r11 section a aSection

  • Seismic Stopper×1rectangular blockreinforced concreteLabeled RCC SEISMIC STOPPER, adjacent to bearing

1070 mm1236 mm80 mm92 mm230 mm3500 mm2650 mm1500 mm+9 more