Drawing → BOQ
← Mindmapwhat the drawings said

Wing Wall

2 pages · 2 crops · ×2 · substructure

Matched toWing Wallbridge.substructure.abutment_system.wing_wallon “Wing Wall”

1 read off the drawings · 4 not established
The class asks forValueHowFrom
LengthLwants m/mmnot establishedThe plan crop shows a hatched fan-shaped area near A1 labeled as wingwall/slope but gives no length dimension for it. The section crop shows the wing wall/return only partially, cut by a break line, with no length callout.not found
Wall ThicknessT_wallwants m/mmnot establishedThe wing wall is described as a small stepped concrete element partially visible with a break line; no dimension line is tied to it specifically.not found
HeightHwants m/mmnot establishedWithout a dimension line owned by the wing wall element itself, height cannot be read or safely derived.not found
Instance CountNwants count1 countPlan crop lists 'Wingwall/Slope hatching' count=1 near A1; section crop lists 'Wing Wall/Return' count=1 near A2. These likely represent one wingwall shown in two different views of the same abutment feature, but no data confirms wingwalls exist at both abutments/piers or multiples per abutment.Each crop independently lists count=1 for the wingwall object it depicts; taking the object count as given in the readings (not summing across crops since they may show the same wall from different views) gives 1.readcheckp1 · p01_r04p2 · p02_r08 abutment section with retaining wall and bored piles
Concrete Gradefcknot establishedMaterial is noted generically as 'reinforced concrete' for the wing wall, but no specific grade/class designation is given in the readings.not found

Worked out by anthropic/claude-sonnet-5 from the readings below, which are the source. A derived value shows its arithmetic — check it against the drawing before it is priced.

How the sheets named it

Wingwall/Slope hatchingWing Wall/Return

Notes on the sheets that carry it

  • p1TO DEWAS (direction arrow)
  • p15000 (TYP.)
  • p1RCC CRASH BARRIER
  • p1C OF EXP. JOINT
  • p1C BRIDGE (RIGHT SIDE)
  • p2POT-PTFE BEARING (TYP.)
  • p2RCC SEISMIC STOPPER
  • p2STONE PITCHIN(G) [partial]
  • p2INDEPENDENT F [partial, likely 'INDEPENDENT FOOTING' or similar]
  • p2600 THK. FILTE [partial, likely 'FILTER']
  • p21200 DIA BORED [partial]
  • p2CAST-IN-SITU PI [partial, likely 'PILE']
  • p2CL OF EXP. JOINT
  • p2CL OF BRG.

Every crop it was read in — the drawing beside what the model took off it

Page 1

crop

p01_r04

page 1 · bridge_deck_and_approach_p01_r04
Original
p01_r04
{
  "view": "Plan",
  "objects": [
    {
      "name": "Abutment",
      "tag": "A1",
      "shape": "",
      "material": "",
      "count": 1,
      "note": "Marked at left with circle symbol, at centerline of expansion joint"
    },
    {
      "name": "Pier",
      "tag": "P1",
      "shape": "",
      "material": "",
      "count": 1,
      "note": "Marked at right with circle symbol"
    },
    {
      "name": "Crash Barrier",
      "tag": "",
      "shape": "linear/rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Labelled RCC CRASH BARRIER, runs along carriageway edge"
    },
    {
      "name": "Deck Slab / Carriageway",
      "tag": "",
      "shape": "rectangular/tapered in plan",
      "material": "",
      "count": 1,
      "note": "Shown in plan with joints/markings, width labelled"
    },
    {
      "name": "Footpath",
      "tag": "",
      "shape": "rectangular",
      "material": "",
      "count": 1,
      "note": "Located adjacent to carriageway, width dimensions given"
    },
    {
      "name": "Expansion Joint",
      "tag": "",
      "shape": "linear",
      "material": "",
      "count": 1,
      "note": "Centerline marked at A1"
    },
    {
      "name": "Drainage/Deck inlet or joint markers",
      "tag": "",
      "shape": "small square symbols",
      "material": "",
      "count": 8,
      "note": "Repeated small square symbols along carriageway, spacing 5000 TYP, possibly scuppers or expansion joint markers"
    },
    {
      "name": "Trees/Vegetation symbols",
      "tag": "",
      "shape": "circular cluster symbols",
      "material": "",
      "count": 10,
      "note": "Landscaping symbols near abutment, likely tree plantation area or embankment slope planting"
    },
    {
      "name": "Wingwall/Slope hatching",
      "tag": "",
      "shape": "tapered hatched area",
      "material": "",
      "count": 1,
      "note": "Hatched fan-shaped area near A1 indicating slope or wingwall footprint"
    }
  ],
  "measurements": [
    {
      "label": "Overall length SQ",
      "value": "40000",
      "unit": "",
      "appliesTo": "A1 to P1 span, square measurement"
    },
    {
      "label": "Overall length SK",
      "value": "46189",
      "unit": "",
      "appliesTo": "A1 to P1 span, skew measurement"
    },
    {
      "label": "Length SQ",
      "value": "37761",
      "unit": "",
      "appliesTo": "partial span measurement, square"
    },
    {
      "label": "Length SK",
      "value": "43603",
      "unit": "",
      "appliesTo": "partial span measurement, skew"
    },
    {
      "label": "Offset SQ",
      "value": "1070",
      "unit": "",
      "appliesTo": "near A1, square"
    },
    {
      "label": "Offset SK",
      "value": "1236",
      "unit": "",
      "appliesTo": "near A1, skew"
    },
    {
      "label": "Offset SQ",
      "value": "1170",
      "unit": "",
      "appliesTo": "near P1, square"
    },
    {
      "label": "Offset SK",
      "value": "1350",
      "unit": "",
      "appliesTo": "near P1, skew"
    },
    {
      "label": "Typical spacing",
      "value": "5000",
      "unit": "",
      "appliesTo": "repeated square symbols along carriageway, TYP"
    },
    {
      "label": "Footpath width",
      "value": "1500",
      "unit": "",
      "appliesTo": "footpath section"
    },
    {
      "label": "Width dimension",
      "value": "450",
      "unit": "",
      "appliesTo": "edge strip near footpath"
    },
    {
      "label": "Width dimension",
      "value": "100",
      "unit": "",
      "appliesTo": "strip near footpath"
    },
    {
      "label": "Width dimension",
      "value": "450",
      "unit": "",
      "appliesTo": "lower left, near carriageway width label"
    },
    {
      "label": "Carriageway width",
      "value": "6550",
      "unit": "",
      "appliesTo": "width of carriageway, partially cut off (appears as '550 WIDTH')"
    },
    {
      "label": "Slab dimension",
      "value": "3500",
      "unit": "",
      "appliesTo": "slab width, near bottom left"
    },
    {
      "label": "Overall left dimension",
      "value": "40000",
      "unit": "",
      "appliesTo": "total width shown at far left vertical dimension"
    }
  ],
  "notes": [
    "TO DEWAS (direction arrow)",
    "5000 (TYP.)",
    "RCC CRASH BARRIER",
    "C OF EXP. JOINT",
    "C BRIDGE (RIGHT SIDE)"
  ],
  "labels": [
    "A1",
    "P1",
    "TO DEWAS",
    "FOOTPATH",
    "C BRIDGE (RIGHT SIDE)",
    "SLAB"
  ],
  "description": "This crop shows a plan view of a bridge approach and deck area between abutment A1 and pier P1, with overall span dimensions given in both square (SQ) and skew (SK) measurements. It details footpath and carriageway widths, an RCC crash barrier along the edge, typical spacing of deck elements at 5000 units, and a landscaped/vegetated area near the abutment with slope hatching, likely representing an embankment or wingwall zone."
}

p01_r04Plan

  • Wingwall/Slope hatching×1tapered hatched areaHatched fan-shaped area near A1 indicating slope or wingwall footprint

40000 Overall length SQ46189 Overall length SK37761 Length SQ43603 Length SK1070 Offset SQ1236 Offset SK1170 Offset SQ1350 Offset SK+8 more

Page 2

crop

p02_r08 abutment section with retaining wall and bored piles

page 2 · structural_drawings_pkg_1_890ff33d80e843ef8aa5a52a7a9de3d8_p02_r08_abutment_section_with_retaining_wall_and_bored_piles
Original
p02_r08 abutment section with retaining wall and bored piles
{
  "view": "Section",
  "objects": [
    {
      "name": "Abutment",
      "tag": "A2",
      "shape": "tapered/trapezoidal",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Abutment section with sloped back face and seismic stopper"
    },
    {
      "name": "Bearing",
      "tag": "",
      "shape": "rectangular",
      "material": "POT-PTFE",
      "count": 1,
      "note": "Labeled POT-PTFE BEARING (TYP.), located at abutment top"
    },
    {
      "name": "Seismic Stopper",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Labeled RCC SEISMIC STOPPER"
    },
    {
      "name": "Expansion Joint",
      "tag": "",
      "shape": "linear gap",
      "material": "",
      "count": 1,
      "note": "Centerline of expansion joint shown with gap dimension"
    },
    {
      "name": "Pile",
      "tag": "",
      "shape": "circular",
      "material": "cast-in-situ concrete",
      "count": 4,
      "note": "1200 dia bored cast-in-situ piles, shown in dashed elevation below abutment"
    },
    {
      "name": "Filter Layer",
      "tag": "",
      "shape": "",
      "material": "granular filter",
      "count": 1,
      "note": "600 THK. FILTER (partial label) shown near ground level"
    },
    {
      "name": "Stone Pitching",
      "tag": "",
      "shape": "",
      "material": "stone",
      "count": 1,
      "note": "STONE PITCHIN(G) label, partial text, embankment slope protection"
    },
    {
      "name": "Approach Embankment/Slope Fill",
      "tag": "",
      "shape": "tapered",
      "material": "granular fill",
      "count": 1,
      "note": "Hatched fill material forming approach slope behind abutment"
    },
    {
      "name": "Wing Wall/Return",
      "tag": "",
      "shape": "rectangular",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Small stepped concrete element near top left, partially visible with break line"
    }
  ],
  "measurements": [
    {
      "label": "Distance from CL BRG to CL EXP JOINT (SQ)",
      "value": "1070",
      "unit": "",
      "appliesTo": "A2 abutment"
    },
    {
      "label": "Distance from CL BRG to CL EXP JOINT (SK)",
      "value": "1236",
      "unit": "",
      "appliesTo": "A2 abutment"
    },
    {
      "label": "Expansion gap (SQ)",
      "value": "80",
      "unit": "",
      "appliesTo": "expansion joint"
    },
    {
      "label": "Expansion gap (SK)",
      "value": "92",
      "unit": "",
      "appliesTo": "expansion joint"
    },
    {
      "label": "Width dimension",
      "value": "3500",
      "unit": "",
      "appliesTo": "top slab/deck near abutment"
    },
    {
      "label": "Vertical dimension",
      "value": "230",
      "unit": "",
      "appliesTo": "deck/slab thickness at top"
    },
    {
      "label": "Vertical dimension",
      "value": "2650",
      "unit": "",
      "appliesTo": "abutment stem height"
    },
    {
      "label": "Horizontal dimension",
      "value": "1500",
      "unit": "",
      "appliesTo": "abutment top step"
    },
    {
      "label": "Horizontal dimension",
      "value": "2850",
      "unit": "",
      "appliesTo": "abutment top area"
    },
    {
      "label": "Horizontal dimension",
      "value": "1500",
      "unit": "",
      "appliesTo": "lower abutment/slope area"
    },
    {
      "label": "Pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "piles"
    },
    {
      "label": "Pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "piles"
    },
    {
      "label": "Pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "piles"
    },
    {
      "label": "Edge distance",
      "value": "750",
      "unit": "",
      "appliesTo": "pile group left edge"
    },
    {
      "label": "Edge distance",
      "value": "750",
      "unit": "",
      "appliesTo": "pile group right edge"
    },
    {
      "label": "Total pile group width",
      "value": "12300",
      "unit": "",
      "appliesTo": "pile group"
    },
    {
      "label": "Pile diameter",
      "value": "1200",
      "unit": "DIA",
      "appliesTo": "bored cast-in-situ piles"
    },
    {
      "label": "Filter thickness",
      "value": "600",
      "unit": "THK",
      "appliesTo": "filter layer"
    },
    {
      "label": "Scale",
      "value": "1:150",
      "unit": "",
      "appliesTo": "Section A-A"
    }
  ],
  "notes": [
    "POT-PTFE BEARING (TYP.)",
    "RCC SEISMIC STOPPER",
    "STONE PITCHIN(G) [partial]",
    "INDEPENDENT F [partial, likely 'INDEPENDENT FOOTING' or similar]",
    "600 THK. FILTE [partial, likely 'FILTER']",
    "1200 DIA BORED [partial]",
    "CAST-IN-SITU PI [partial, likely 'PILE']",
    "CL OF EXP. JOINT",
    "CL OF BRG."
  ],
  "labels": [
    "A2",
    "SECTION A-A",
    "(SCALE 1:150)"
  ],
  "description": "This crop shows a cross-section (Section A-A) through abutment A2 of a bridge, illustrating the abutment stem, bearing arrangement (POT-PTFE bearing with RCC seismic stopper), expansion joint gap dimensions for square and skew geometries, backfill and slope protection details, and a row of four bored cast-in-situ piles with spacing dimensions below the abutment. It documents structural and geometric details needed for abutment, bearing, and foundation pile quantities."
}

p02_r08 abutment section with retaining wall and bored pilesSection

  • Wing Wall/Return×1rectangularreinforced concreteSmall stepped concrete element near top left, partially visible with break line

1070 Distance from CL BRG to CL EXP JOINT (SQ)1236 Distance from CL BRG to CL EXP JOINT (SK)80 Expansion gap (SQ)92 Expansion gap (SK)3500 Width dimension230 Vertical dimension2650 Vertical dimension1500 Horizontal dimension+11 more